A vertical two start square threaded screw of a (100 mm) pitch diameter and (20 mm) pitch supports a vertical load of (18 kN). The axial thrust on the screw is taken by a collar bearing of (87.5 mm) mean radius. Find the force required at the end of a lever which is (400 mm) long in order to lift and lower the load. The coefficient of friction for the vertical screw and nut is (0.15) and that for collar bearing is (0.2). Also, find the overall efficiency for the two cases.

A vertical two start square threaded screw of a (100 mm) pitch diameter and (20 mm) pitch supports a vertical load of (18 kN). The axial thrust on the screw is taken by a collar bearing of (87.5 mm) mean radius. Find the force required at the end of a lever which is (400 mm) long in order to lift and lower the load. The coefficient of friction for the vertical screw and nut is (0.15) and that for collar bearing is (0.2). Also, find the overall efficiency for the two cases.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The pressure distribution at the pivot bearing's surface of contact changes, as indicated. Determine the torque M necessary to overcome friction if the shaft sustains an axial force P and the coefficient of static friction is.
3. A square threaded bolt of mean diameter 24 mm and pitch 5 mm is tightened by screwing a nut whose mean diameter of bearing surface is 50 mm. If the coefficient of friction for the nut and bolt is 0.1 and for the nut and bearing surfaces 0.16, find the force required at the end of a spanner 0.5 m long when the load on the bolt is 10 kN.
The lead screw of a lathe has Acme threads of 60 mm outside diameter and 8 mm pitch. It supplies drive to a tool carriage which needs an axial force of 2000 N. A collar bearing with inner and outer radius as 30 mm and 60 mm respectively is provided. The coefficient of friction for the screw threads is 0.12 and for the collar it is 0.10. Find the torque required to drive the screw and the efficiency of the screw.
draw free body diagram and A and B please. picture is pretty clear! Block is labeled A (under A is 25 degrees) above is 45 degrees and F pulling down is 50 degrees
(a) A body of weight 45 N is placed on a rough horizontal plane. To just move the body on the horizontal plane, a push of 25 N inclined at 11° to the horizontal plane is required. Find the coefficient of friction. (b) Determine the number of members in a structure, if the total number of joints in the structure is 3. Enter your student ID in the box and upload your handwritten answers in the separate link provided.
I need the answer as soon as possible
Q3/ A screw-jack is used to lft a load of 4 kN. The screw of the screw-jack is square threaded with two threads to 1 cm. If the co-efficient of friction between the nut and screw is 0,095 and outer diameter of screw s 6 cm, find the force required atthe end of the handle of length 50 cm to ift the load. (20 M)
The root diameter of a triple threaded power screw is 550 mm It has a pitch of 10 mm It is used to lift a load of 15 kN. The collar of the screw has an outside diameter of 100 mm and an inner diameter 60 mm Find the force applied at a radius of 950 mm if the coeffcient of friction for both threads and collar is 0.20.
Show full and complete solution
The clamp exerts a 145 lb compressive force on the wood blocks. Single-threaded screw BC has lead L = 0.190 in. and mean diameter d = 0.370 in. It turns in the threaded sleeve at C and pushes against B. The coefficient of static friction between the screw threads and the threaded sleeve is = 0.300. Neglect friction at B. 2 in. 2 in. 2 in. B 2.25 in. 2.40 in. 2.25 in. (a) Determine the value of the moment M in ft · Ib to increase the clamping force. (Enter the magnitude.) ft · Ib (b) Determine the value of the moment M in ft · Ib to decrease the clamping force. (Enter the magnitude.) ft · Ib
In the old-fashioned printing press of Fig. square-threaded screw is used to press the paper against the type bed. The single-threaded screw has a mean radius of 20 mm and a lead of 100 mm. The coefficient of friction is 0.15, and the clamping force necessary to guarantee clear printing on all parts of the paper is 400 N. Determine the twisting moment necessary to operate the press and whether or not a moment must be applied to release the press. P
Provide an FBD in this given problem