A vertical power screw with double start square threads of 50 mm mean diameter and 11mm pitch is raised against a load of 10 kN by means of a hand wheel, the boss of which is threaded to act as a nut. A thrust collar, taking up the axial load,supports the wheel boss and has a mean diameter of 60mm. The coefficient of friction is 0.18for the screw and 0.16for the collar. If the tangential force applied by each hand to the wheel is 200 N, find suitable diameter of the hand wheel.

Q: Determine the force required to raise a load of 3100 lbs., when a 2.5 in. triple threaded square…

A:

Q: An elevator type lift is being designed to raise a load up to 5,000pounds between floors.…

A: Data given- Raise a Load = 5000 pounds  Elevator weight =  800 pound Two square-thread lead screws D…

Q: A power screw has single square threads. It has a major diameter of 38 The coefficient of friction…

A: Given data: Major diamter, d0 = 36 mm pitch (p) = 6 mm co-efficient of friction for the threads =…

Q: A turnbuckle, which is used to adjust tension in cables, is subjected to tension T=184.7 N as shown.…

A: Given data: The tension in the cable, T = 184.7 N. The lead of screw, L = 0.005 m. The nominal…

Q: PROBLEM 14: P C h A 24 in. IT B A 120-lb cabinet is mounted on casters that can be locked to prevent…

A:

Q: The device shown is used for coarse adjustment of the height of an experimental apparatus without a…

A: Coefficient of friction is μs=0.32. The equilibrium condition is obtained under the following…

Q: B) A body is pulled by a rope which passes 3 times round a power-driven capstan 600 mm diameter,…

A:

Q: The screw jack of Fig. screw having a coefficient of friction of 0.35 and a mean ra- dius of 1 in.…

A: Write the formula for the angle of friction. The lead is maximum when the lead angle is maximum.…

Q: A trapezoidal-threaded power screw with a crest diam- eter of 30 mm and single thread is used to…

A: Given : crest diameter, dc = 30 mm  load, W = 50 KN collar mean diameter, D = 40 mm  coefficient of…

Q: THE ENGINE OF AN AUTOMOBILE IS RATED TO GIVE SOKWAT 200 RPM WITH A MAXIMUM TORQUE OF 600 N-M. DESIGN…

A: The answer is mention below

Q: Q1) The V thread of a screw jack has a single start with out side diameter 40 mm and 6 mm pitch. The…

A: There are two types of forces that are acting on a circular surface. One type of force is Radial…

Q: 1 double-threaded powe Screw. with ISO metric trapezoidal threads is used to raise (a load of 300…

A:

Q: 3. What is the minimum static coefficient of friction required to maintain the bracket (light…

A: Consider the free-body diagram for the system as shown below.

Q: Two workers are carrying a 50-mm thick panel by means of panel carriers, one of which is shown in…

A:

Q: Specify the required torque M on the power screw necessary to overcome a resistance of 490 N to…

A:

Q: =ust is carried on a collar of 100 mr er and 60 mm inner diameter. The ficient of friction at the…

A:

Q: solve show solution for answer given

A: Answer:Explanation:

Q: A power screw has single square threads. It has a major diameter of 36 mm and a pitch of 6 mm. The…

A:

Q: single square-thread screw has an input power of 3 kW at a speed of 1 rev/s. The screw has a…

A:

Q: The disc clutch has a pair of mating friction surfaces, with an outer diameter of 350 mm and an…

A: Given data:- outer diameter=350 mm inner diameter =250 mm The average value of the coefficient of…

Q: An axial load of 160 lb is applied to the end bear- Fig. ses place over an annular ring of radius 4…

A: Given that, Axial load applied, P=160 lb,Inner radius of ring, r=4 in,Outer radius of ring, R=7…

Q: ind the work to be done in drawing the coaches together a distance of 200 mm against a steady load…

A: Pitch, P=10 mm=0.01 m,Mean Diamter, D=30 mm=0.03 mThreads are single start type,Coefficient of…

Q: A 5/8-11 unc x1.75 long grade 8 bolt clamps an assembly as shown. A total load (P)of 11500 lbs is…

A:

Q: the bolt is

A:

Q: At stationary the tension in pulley 120N. Find tension in each side and Power tran when belt is on…

A:

Q: A cylinder is moving a 6000 lb load up a 20° slope as shown in the figure below. The friction…

A: Given: Angle of inclination→θ=20° Friction coefficient between the surfaces→μ=0.4 Mass of the…

Q: Problem -02 Dry FrictionKnowing that a couple of magnitude 30 N m is required to start the vertical…

A:

Q: HW9 In an engine governor of the Porter type, the upper and lower arms are 300 mm and 350 mm…

A: Introduction: A governor is a mechanism that is used to keep an engine's mean speed within set…

Q: ces is 0.4. The pitch of the thread on the shaft is 5 mm. Take the mean radius of the screw to be 15…

A: Given: Mass of block A = 60 kg μk1 = 0.3 For all non thread contacts L = 5mm = 0.005 m r = 15 mm =…

Q: A 500-N concrete block is to be lifted by the pair of tongs shown. ON 315 mm 500 N D G 105 mm…

A:

Q: A basic single-thread, square-threaded screw jack is shown. It is designed to lift a load F that…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.