a) Using the following variables write a single line MATLAB codes to retrive given output. (You need to use at least two of the variables for each solution. Using scalar values is allowed along with the variables)(Hint: consider logicals for some of them). A = [7777); B= 6:9; C= 3; D = 2; E = 8; F=[C,D,E,D}; i.) [111 1) = ? ii.) [001 0] = ? iii.) [10.0000 10.5000 11.0000 11.5000] = ? iv.) [0100] = ? v.) [3 7; 27;87; 2 7;) = ?

a) Using the following variables write a single line MATLAB codes to retrive given output. (You need to use at least two of the variables for each solution. Using scalar values is allowed along with the variables)(Hint: consider logicals for some of them). A = [7777); B= 6:9; C= 3; D = 2; E = 8; F=[C,D,E,D}; i.) [111 1) = ? ii.) [001 0] = ? iii.) [10.0000 10.5000 11.0000 11.5000] = ? iv.) [0100] = ? v.) [3 7; 27;87; 2 7;) = ?

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Identify the base case in this recursive function. Assume i> 0 when the function is invoked. (Line numbers are not part of the code.) 1. def add(i, j): 2. if i == 0: 3. return j 4. else: 5. return add(i - 1, j + 1) This function has no base case O line 5 line 1 line 4 O line 2 Question 6 The following recursive function is supposed to return a list that is the reverse of the list it was given. But it has a bug. What is the bug? (Line numbers are not part of the code.) MooP eok Dr
Attempt to unify the following pairs of expressions. Either show their most general unifiers or explain why they will not unify. p(A,B,c) and p(Q,r,S)
None
2. Consider the following function: def func1(n): output = 1 for i in range (1, n) : output = i return output Rewrite the function as a recursive function.
Please solve quickly
Solve Q-1 (to print matrix) in C++ language with proper comments
If you have trouble reading the picture please let me know. 8. (a) Write behavioral Verilog code for a module called “Sort2” (pictured below) with three inputs s, a, b and two outputs x, y. The module’s function is also described below; in the function table, a “–” represents a don’t care. Also the function table has s, a as inputs, but the outputs x, y are expressed in terms of the third input b. In words, the “function table” to the left translates to the following: When s = 0, the smallest value among a and b goes to x and the other value goes to y. When s = 1, the largest value among a and b goes to x and the other value goes to y. (b) Structurally connect copies (or instantiations) of the module Sort2 to construct the module Bitonic with four inputs a0,a1,a2,a3 and four outputs z0,z1,z2,z3 shown below; each box in the figure below represents an instantiation of Sort2. Further, the inputs and outputs of the instantiations are located as in the figure above; namely, input to…
Write the negation of each of the following statements (hint: you may have to apply DeMorgan’s Law multiple times) Please show work
Choose the correc answer in the question below.