A) Use nodal analysis to find the voltage drop across 32 resistor (Vo) in the circuit given in Figure A. [1 Clearly identify/label all node voltages including reference node. Write clearly all required KCL equations and solve them to find unknown. 20 42. 60. 10V 20 202 Figure A: Circuit to find current through 52 resistor

A) Use nodal analysis to find the voltage drop across 32 resistor (Vo) in the circuit given in Figure A. [1 Clearly identify/label all node voltages including reference node. Write clearly all required KCL equations and solve them to find unknown. 20 42. 60. 10V 20 202 Figure A: Circuit to find current through 52 resistor

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 4PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

What is the load current for the circuit shown in the figure? Please choose one: a. 9.0 mA b. 7.5 mA c. 3.0 mA D. 6.0 mA
A chopper is employed to charge a battery as shown in figure. The charging current is 5 A. The duty ratio is 0.2. The chopper output voltage is also shown in the figure. The peak to peak ripple current in the charging current is https://practicepaper.in/wp-content/uploads/GATE/EE/20031/q87.jpg
H.w For the circuit show n figure ca Iculate the expre ss ion of tne assume t he in i tial value of in ductor .initial value of cap acit or is zero o'lf th o'5 F
Compute for the following values and show compelete solutions. Find the following: A.) isc B.) iN C.) VN D. Draw circuit equivalent
Using The Constant Voltage Drop (CVD) Model, please get V and I
B.. What is the load current for the circuit shown in the figure? Please choose one: a. 6.0 mA b. 3.0 mA C. 9.0 mA D. 7.5 mA
The voltage regulation can be equal to zero when: O The t and current is not too high. OThe p.f. is leading p.f. for any possible current. OThe p.f. is lagging p.f. for rated current.
For a combined circuit digram, what should we do first? what will happen to the resistance? what will happen to the voltage? what will happen to the current? Please give an explanation to a combined circuit diagram.
1. The no-load terminal voltage of a battery is 30 V. The terminal voltage drops to 22 V when supplying a current of 5 A. Determine the emf and the internal resistance of this battery. Ans. r= 1.6 ohm 2. Two identical zinc carbon batteries are available. When connected in series, they supply 0.5 A to a 4 ohm resistor. When connected in parallel, they supply 0.4 A to a 5 ohm resistor. Determine the emf and internal resistance of each battery. Ans. 2.667 V and 3.333 ohm 3. When supplying a current of 5 A, the terminal voltage of a battery is 15 V. The battery is then recharged at a rate of 3 A and the terminal voltage is found to be 21 V. Determine the emf and the Internal resistance of the battery. Ans. 18.75 V and 0.75 ohm 4. A battery with an emf of 12 V and an internal resistance of 0.8 ohm is to be recharged through a 20 V source. (a) show by means of a diagram the connection of the circuit elements. (b) What is the current in the circuit? (c) The recharging current is to be…
4. From the figure shown which is series-parallel, the following values are: ID ohms in series with the parallel combination of 30 and DD ohms respectively. If the supply voltage is bD volts, find the following: a) equivalent resistance b)total current c)individual current d)current at 3D and D ohms only
Instructions Calculate the DC voltages and currents in the circuit. Find for the current emitter, collector current and collector voltage. +12v 5kN 5kN Von Voz Q2 Vi2 2.7kN
In the circuit below, we have a Zener Diode circuit with a load, RL. Use the same measurements for source voltage V1 and resistor R3 resistance as in the circuit schematic. V1 -15V R3 2700 D1 1N753A RL Determine the lowest possible value for the load RL, so that the voltage drop across it is equal to the Zener voltage. For your diode, use model Zener 1N753A. This diode has a Zener voltage of 6.2V, a Zener current of 60mA, a Zener impedence of 72, and a test current of 20mA.