A uniform, solid sphere of radius 5.75 cm and mass 4.75 kg starts with a purely translational speed of 1.75 m/s at the top of an inclined plane. The surface of the incline is 2.75 m long, and is tilted at an angle of 27.0∘ with respect to the horizontal. Assuming the sphere rolls without slipping down the incline, calculate the sphere's final translational speed v2 at the bottom of the ramp.

A uniform, solid sphere of radius 5.75 cm and mass 4.75 kg starts with a purely translational speed of 1.75 m/s at the top of an inclined plane. The surface of the incline is 2.75 m long, and is tilted at an angle of 27.0∘ with respect to the horizontal. Assuming the sphere rolls without slipping down the incline, calculate the sphere's final translational speed v2 at the bottom of the ramp.

Similar questions

One popular design of a household juice machine is a conical, perforated stainless steel basket 3.30 cm high with a closed bottom of diameter 8.00 cm and open top of diameter 13.40 cm that spins at 23000 revolutions per minute about a vertical axis. Solid pieces of fruit are chopped into granules by cutters at the bottom of the spinning cone. Then the fruit granules rapidly make their way to the sloping surface where the juice is extracted to the outside of the cone through the mesh perforations. The dry pulp spirals upward along the slope to be ejected from the top of the cone. The juice is collected in an enclosure immediately surrounding the sloped surface of the cone. Pulp D Motor Spinning basket Juice spout (a) What centripetal acceleration does a bit of fruit experience when it is spinning with the basket at a point midway between the top and bottom? m/s² ---Direction--- (b) Observe that the weight of the fruit is a negligible force. What is the normal force on 1.50 g of fruit at…
A tire is rotating at an angular velocity of 51.6 radians/s. The radius of the tire is 1.9 m. Find the linear speed/velocity of a point on the edge of the tire.
A solid cylinder of mass 2.7 kg and radius 0.48 m starts from rest at the top of a ramp, inclined 28°, and rolls to the bottom without slipping(For a cylinder I =; 0.5MR^2) The upper end of the ramp is 2.3 m higher than the lower end. Find the linear velocity of the cylinder when it reaches the bottom of the ramp? (g = 9.8 m/s^2)
A car is designed to get its energy from a rotating flywheel in the shape of a uniform, solid disk of radius 0.650 m and mass 600 kg. Before a trip, the flywheel is attached to an electric motor, which brings the flywheel's rotational speed up to 5.30 ✕ 103 rev/min. (a) Find the kinetic energy stored in the flywheel (in J). (b) If the flywheel is to supply energy to the car as a 12.0 hp motor would, find the length of time in hours the car could run before the flywheel would have to be brought back up to speed.
A child sits on a merry‑go‑round that has a diameter of 6.00 m. The child uses her legs to push the merry‑go‑round, making it go from rest to an angular speed of 18.0 rpm in a time of 37.0 s. What is the angular displacement Δθ of the merry‑go‑round, in units of radians (rad), during the time the child pushes the merry‑go‑round?
A uniform, solid sphere of radius 6.00 cm and mass 4.50 kg starts with a purely translational speed of 2.50 m/s at the top of an inclined plane. The surface of the incline is 2.00 m long, and is tilted at an angle of 32.0∘ with respect to the horizontal. Assuming the sphere rolls without slipping down the incline, calculate the sphere's final translational speed v2 at the bottom of the ramp. v2= m/s
You find an interesting looking ball but can't tell if it's solid or hollow, so you design an experiment: The mystery ball is rolled along a horizontal surface with an initial translational speed of v= 2.7 m/s. Then the ball rolls up an incline and eventually stops after climbing up a vertical distance of h = 0.52 m, as shown in the figure. Based on your experiment, is the ball solid or hollow? Use calculations to support your answer. Assume the ball rolls without slipping. Note: you do not need to know the mass or radius of the ball to answer this problem. 1フ

A turntable 46.0 cm in diameter diameter starts from rest, and rotates at 68.0 rpm at its first complete revoļution with constant angular acceleration. If it maintains the same acceleration, a) what is the rotational speed at time 34.0 seconds? b) what is the tangential speed of a point 10 cm from the edge of the turntable at time 34.0 seconds? Enter answer "O" in the answer box. Submit in the corresponding folder (or email) your solution by 3:50 pm, include a sketch/drawing of the rotating wheel, and a step- by-step solution.
A car is designed to get its energy from a rotating flywheel in the shape of a uniform, solid disk of radius 0.650 m and mass 540 kg. Before a trip, the flywheel is attached to an electric motor, which brings the flywheel's rotational speed up to 5.30 ✕ 103 rev/min. HINT (a) Find the kinetic energy stored in the flywheel (in J). J (b) If the flywheel is to supply energy to the car as a 12.5 hp motor would, find the length of time in hours the car could run before the flywheel would have to be brought back up to speed.
A car is designed to get its energy from a rotating flywheel in the shape of a uniform, solid disk of radius 0.800 m and mass 600 kg. Before a trip, the flywheel is attached to an electric motor, which brings the flywheel's rotational speed up to 5.30 ✕ 103 rev/min. (a) Find the kinetic energy stored in the flywheel (in J). (b) If the flywheel is to supply energy to the car as a 10.5 hp motor would, find the length of time in hours the car could run before the flywheel would have to be brought back up to speed.