A two spans continuous concret beam is to be Supported by three concreted columns spaced (8,50 m) on centers. A service live load of (18 kN/m) is to be carried in addition to the weight of the beam A limited cross sections area to be used with (b=400mm, (h=600mm) with two layers reinforcement, Find the area of reinforcement at section (b-b) Use fy=280 μPa and fc = 21 MPa, in Assume columns width=400 mm.

A two spans continuous concret beam is to be Supported by three concreted columns spaced (8,50 m) on centers. A service live load of (18 kN/m) is to be carried in addition to the weight of the beam A limited cross sections area to be used with (b=400mm, (h=600mm) with two layers reinforcement, Find the area of reinforcement at section (b-b) Use fy=280 μPa and fc = 21 MPa, in Assume columns width=400 mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Design the reinforcement of a rectangular beam to resist a dead load moment of 200kN.m (including its own weight) and a live load moment of 300kN.m. The beam is limited in size to 350mm by 600mm overall depth. Steel covering from centroid of bars to outermost fiber is 100mm for both tension and compression reinforcement. Use fc'=27.5Mpa, fy = 414MPa,20mm barsA. As'= 7 of 20mm and As=14 of 20mmB. As' = 9 of 20mm and As=18 of 20mmC. As'= 5 of 20mm and As=10 of 20mmD. As' = 3 of 20mm and As=6 of 20mm Please provide neat and clear solutions Note: kindly check below answer
A beam has a width of 350 mm and a total depth of 700 mm. The loading is as shown in the figure. Material strengths are fc’ = 32 MPa, fy = 400 MPa, and a stirrups diameter of 10 mm. Consider the spacing requirements a. Determine the numbers of 25 mm diameter for bottom reinforcement. b. Unity ratio of the designed section Show complete solution. Need ASAP. thank you.
A rectangular beam which is limited to 350 mm by 650 mm is reinforced at the compression side with As’ = 1,000 mm2and on the tension side As = 4,000 mm2. The beam has an effective depth of 510 mm and its neutral axis is located at 127.84 mm below the top of the beam. Assume steel in tension yields but that in compression does not yield. F’c = 35 MPa, β = 0.81, fy = 400 MPa. Steel covering on top is 50 mm. Determine stress of steel in compression. Determine the depth of compression stress block. Determine the moment capacity of the beam.
Design the slab reinforcement if the maximum positive moment is Mup= wul2/11 and the maximum negative moment is Mun= wul2/10. Given: Superimposed dead load = 4.76 kPa Live Load = 1.9 kPa Weight of slab = 3.45 kPa Thickness = 150 mm Length = 23.8 m Span = 3m
A reinforced concrete beam has a width of 250mm and an effective depth of 500mm. If F'c= 28MPa, Fy = 415MPa, determine the following: a. Maximum steel area for singly reinforced condition. b. Maximum design strength if the beam is singly reinforced. c. The required steel area if the beam is subjected to a dead load moment of 100KN.m and live load moment of 130KN.m.
Design the reinforcement of a rectangular beam to resist a dead load moment of 200kN.m (including its own weight) and a live load moment of 300kN.m. The beam is limited in size to 350mm by 600mm overall depth. Steel covering from centroid of bars to outermost fiber is 100mm for both tension and compression reinforcement. Use fc'=27.5Mpa, fy = 414MPa,20mm barsA. As'= 7 of 20mm and As=14 of 20mmB. As' = 9 of 20mm and As=18 of 20mmC. As'= 5 of 20mm and As=10 of 20mmD. As' = 3 of 20mm and As=6 of 20mm Please provide neat and clear solutions
a concrete floor slab 100mm thick is cast monotholic with concrete beams 2.0 m on centers. the beams have a span of 4.0m, web width of 259 mm and overall depth of 50 mm. the tensile reinforcement consists of 6-⌀20 mm bars in two rows with 25mm vertical clear spacing. use material strengths f'c=21MPa and fy=415MPa. calculate the ff considering a T-geometry: 1. effective flange width of an interior beam in mm 2. depth of uniform stress block at ultimate stage in mm to the nearest whole number 3. tensile steel strain compatible strain of 0.003
Problem 5.23 With f, = 60,000 psi and f = 4000 psi, select the reinforcing for T beam AB for the floor system shown. Assume simple supports at A and B. The live load is to be 100 psf, while the dead load in addition to the concrete's weight is to be 80 psf. Concrete is assumed to weigh 150 lb/ft. The slab is 4 in. thick, d is 24 in., and b, is 16 in. (Ans. 3.84 in.², use 4 #9 bars) edge L. beam 5 ft 1 B T beams -4 @ 10 ft=40 ft- 5 ft 30 ft
A reinforced concrete beam that is 375 mm wide and 500mm deep must resist a service live load moment of 250 kN-m and a service dead load moment of 150 kN-m. Use f'c-21 MPa and fy=415 MPa. The effective concrete cover is 65mm (to the centroid of reinforcements). 1. Determine the area of compression steel reinforcement (If required. Answer O if not) in mm² 2. Determine the minimum number of 25 mm diameter bars to be provided to satisfy the demand ultimate moment 3. Determine the maximum number of 25 mm diameter bars to be provided to have a tension controlled section Answer 1: 2403.21 correct answer: Answer 2: 9.00 Answer 3: 8.00
Problem # 1. A rectangular has a width of 300 mm and an effective depth of 460 mm. The beam is reinforced with 2-28 mm dia. at the top. fc'=35 MPa, fy = 350 MPa a. Compute the ratio of the depth of compression block to the distance of the top fiber to the neutral axis. b. Compute the balanced steel ratio of the reinforcement. c. Compute the max. area of the steel permitted.
A reinforced concrete beam has a width of 300 mm and effective depth of 500mm to the centroid of the tension reinforcements. Consider the steel reinforcements will be placed in a single layer arrangement. Concrete strength fc’ = 34.5 MPa. Determine the steel ratio of the section if the beam is singly reinforced with the maximum amount of steel for transition control allowed by the Code if the bars has a steel strength of fy = 345 MPa. Determine the steel ratio of the section if the beam is singly reinforced with the maximum amount of steel for tension control if the bars has a steel strength fy = 345 MPa. Determine the number of pieces of 28 mm ᴓ bars required for the section if the beam is singly reinforced with the maximum amount of steel for tension control if the bars has a steel strength fy = 415 MPa.
Find the ultimate moment of resistance for the rectangular section reinforced as shown below. material strengths: Concrete Reinforcement Width of section Reinforcement fcu= 30-MPa fy:= 450-MPa b:= 280 mm d:= 510 mm d':= 50-mm 2 A, 2410-mm A's:= 628-mm 2 b A', Hi As