A triangular lot ABC has all points on a circle with radius 25m. AC, which is along the horizontal, lies on the diameter of the circle. If BC measures 30m, determine the bearing of AB, BC, and CA. Assume that the corners of the lot are labeled in a clockwise direction.

Q: Draw and label the different types of trusses according to their classifications as to Simple,…

A: A simple definition of Truss would be as:- A truss is an assembly of members connected by nodes that…

Q: a. calculate the forces on the rod by using analysis(calculation) method

A: Note - We’ll answer the first question since the exact one wasn’t specified. Please submit a new…

Q: How many inches of 1/8-in weld are necessary to transfer a shear force of 6000 lb from one plate to…

A: The objective of the question is to find out the length of the weld required to transfer a shear…

Q: a.) Girder factor at joint D, go b.) Column factor at joint K, Ck C) Girder moment factor at Joint…

A: All data mentioned in the figure it selfneed to find 1- girder factor at joint D, gD2- column factor…

Q: 7. Compute the tensile capacity for the A36 steel plate shown. Bolts are 7/8 in diameter. Neglect…

A: For A36 steelUltimate Tensile Strength, fu = 58,000 psiYield Tensile Strength, fy = 36,300 psiThe…

Q: 1. Identify zero force memeber. (Draw the FBD of Joint contain zero force member) B H|100 kN 60 kN K…

A: Identify the zero force member (Draw the FBD of joint contain zero force member).

Q: Classify the structure below. Fill in the blank if determinate, or indeterminate, or unstable CH 대

A:

Q: Required: block shear strength of the gusset plate.

A: Plate 6 x 1/2 weld length in shear = 71/2 weld length in tension = 6 in thickness of plate t = 1/2…

Q: FBD= FCD FCE- kips, kips, kips.

A:

Q: Verify the value of ry given in Part 1 of the Manual for the double-angle shape 2L5x31⁄2 x 1⁄2 LLBB.…

A: Calculate the moment of inertia about y-axis: Where; I is the moment of inertia about the y-axis A…

Q: Compute A,, and A, for a 14-in.-wide and ½-in.-thick plate subject to tensile loading with staggered…

A: Given : Width = 14 inches Thickness = 1/2 inches Compute An and Ae for the given plate ?

Q: indeterminate? a) c) b) Hinge www

A: To check whether the structures given are indeterminate or not.   Note: As per the guidelines of…

Q: use autocad Draw the structural details of the following sections (an elevation view and a side…

A:

Q: Answer it complete solutions

A: Step 1:Step by step procedure is written Step 2: Step 3: Step 4:

Q: A D E 1.H Section 2. Wide-Flange 3. American Standard 4. Unequal Leg Angle 5. C Section 6.T Section…

A: Matching the cross section

Q: Determine the force in members FI, EG, FG, GI, JL, KM, JK, JH, GH and HI using Method of Sections.…

A:

Q: Draw a complete, clearly labeled, FBD of member AE.

A: Draw a complete, clearly labeled, FBD of member AE.

Q: use autocad -  Draw the structural details of the following sections (an elevation view and a side…

A: To draw the structural details of a steel connection in AutoCAD, you'll need to include both…

Traverse Survey

Traverse surveying is a popular method of surveying. Traversing is that type of survey where several connected survey lines form a framework and the directions and lengths of the survey lines are measured with the help of a tool to measure angles and tape or chain respectively. Traverse networks involve placing survey stations in a queue or trail and using pre-tested points as a basis for looking at the next point. This type of surveying is different from Tacheometric surveying, where only angles are measured and the process of chaining is reduced.