A transmission shaft consists of two parts: 2m long and 50 mm diameter solid aluminumshaft is to be connected to a hollow steelshaft of the same length and 62 mm outsidediameter . Determine the inside diameter ofthe hollow shaft if the stiffness of Shaft T/e=7800 Nm/rad.. Take the modulus ofrigidity of the steel twice of that ofaluminum. Gsteel=80 GN/m2.9:27 AMV

Answered: Image /qna-images/answer/021e378c-9773-448b-8ee0-76ca24ff20f0.jpg

Answered: A transmission shaft consists of two…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What is the power (?) lost to main crankshaft friction in a four-cylinder engine with a 100mmbore and stroke if the engine is operating at 1500 rpm? Assume the main crankshafthas five bearings, each with a diameter of 50 mm and length of 25 mm.
i need the answer quickly
For the given ball bearing find out the dynamic load value when the Equivalent load is 14836.2N and the Life of the bearing is 1238x10 revolutions. O a. 159305.06 O b. 139227.09 O c. 169418.59 O d. 80407.14 Finish attemp hp
2a-e. Outline five transmission problems its causes and their solutions.
The bearing for a power transmission arrangement is required to carry an equivalent radial load of 2.4 kN at 3000 rpm. The nominal shaft diameter at the bearing is 30mm. A life of 8760 hours is required. Select and specify an appropriate bearing from the limited range available in Tables 9.6 to 9.8. 9.8
Consider that fit between the shaft and the disk is of transition type where the maximum interference is required to be 0,013 mm. Nominal diameter of the shaft is 65 mm. The hole in the disk is machined to IT quality of 7. tolerence on the fit is 0.050 mm. Using the basic shaft system, determine the nearest fit from ISO tables.
!
Please don't provide handwrittenh solution.
Compute the contact stress number for the gear fain pair driven directly by an electrical motor. The driven machthe is concrete mixture with moderate shock, the other data are given below. Ks= 1.00, Km 1.21, Vt =1527 St/min, Av-11 Pd= 6, np= 1750rp.m, Np 20, No= 70, F=2.00/n Tp = 900ib, Dp= 3:333 in The material used for pioin an gear is Steel
Which one is defined as the ratio of the number of bearings which have successfully completed L' million revolutions to the total number of bearings under test. Select one: O a. Failure rate O b. Life of bearing Reliability Od. Efficiency
A) A shat of diameter of d= 35 mm is subjected to a torque varying between 100 N.m to 500 N.m. The SCF due to keyway is 1.5, Su = 500 MPa, S', = 200 MPa. Correction factor for torsion=0.6. Surface finish factor=0.85 and size factor=0.82. Find the value of fatigue factor of safety F.S. Is the design of the shaft safe or not? And why?
I want proper solution don't copy from others solution I will report. flange coupling connects two 50 mm diameter lengths of commercial shafting. The coupling flanges are bolted together with four bolts of the same material as the shaft. The bolts are set in clearance holes. The diameter of the bolt circle is 240 mm and the flange thickness is 22 mm, (1) Determine the minimum bolt diameter required to transmit the same torque that the shaft can transmit.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A transmission shaft consists of two parts: m long and 50 mm diameter solid aluminur shaft is to be connected to a hollow steel shaft of the same length and 62 mm outsic diamoter Dotornmine the inside diamoter o