A transmission line carrying 33kV, 3000A is connecting Al Seeb and Al Gubrah. The concerning substation has the setup of CT and a small range ammeter of (0-30A) connected in the measurement system to measure the current. Then, the number of turns of windings on both primary and secondary of CT (N1 & N2) are calculated as, O a 100, 1 turns O b. 50, 1 turns O G1. 50 turns O d. 1, 100 turns

A transmission line carrying 33kV, 3000A is connecting Al Seeb and Al Gubrah. The concerning substation has the setup of CT and a small range ammeter of (0-30A) connected in the measurement system to measure the current. Then, the number of turns of windings on both primary and secondary of CT (N1 & N2) are calculated as, O a 100, 1 turns O b. 50, 1 turns O G1. 50 turns O d. 1, 100 turns

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Convert followin BCD number into the EX-3 code 1011 1001
On site plans, all evevations are referenced from_. A. The centerline of a street B. Ground level C. A bench mark D. A test boring
8) In Staircase ramp type digital voltmeter contains DC amplifier with a fixed gain of ___________. 1 1000 100 10
explan properly, don't copy, handwritten not allowed,
The MRT train system has two substations within the 10 kilometers stretch with 650 volts and 580 volts, respectively. The resistance of the train system wire and rail return is 0.4 ohm per kilometer. The car, located 4 kilometers from the 650-volt station, draws 200 A from the line.a) What is the load voltage?b) Determine the current supplied at 650-volt substation. Answer in 1 decimal place.c) Determine the current supplied at 580-volt substation. Answer in 1 decimal place.
1. The only exception to the need for all information technology equipment to be satisfactorily grounded is where the equipment is A. DC powered.B. backup generator powered. C. double-insulated.D. isolated equipment. 2. Which section of the National Electrical Code lists sizing requirements for wire-type equipment grounding conductors? A. 250.66 B. 250.118 C. 250.4 D. 250.122 3. Which of the following statements about grounding electrical equipment is true?A. If no wire-type equipment grounding conductors are present with the branch circuits, the equipment grounding terminal bar isn't required.B. Grounding electrical equipment increases the possibility of metal parts remaining energized.C. The nonmetal parts of some electrical equipment are required to be connected to an equipment grounding conductor. D. Equipment grounding conductors can be spliced together outside of a grounded metal box. 4. Which of the following is a condition that must be met in order to qualify for the exemption…
Kindly choose the correct answer. Please answer it ASAP if you can, thanks
Explain each option & Choose the correct option. 4) The _ calculated load is rarely placed on an electrical system.A. optionalB. standardC. total 5) What's the primary disadvantage of using copper conductors?A. CostB. AvailabilityC. Weight 6) You're evaluating the components of a multioccupancy building that won't have an on-site employee. To be compliant with the NEC, each occupant will need to have access to their ownA. service-disconnecting means.B. service conductor.C. cable attachment point.D. emergency fire water pump disconnect ..
Explain in your own words and your own understanding (avoid plagiarism) why is it important to calculate the Percentage Voltage Regulation of an Electrical Equipment or System?
IMC encased in a concrete slab, on the first floor of an office building, is considered a _____ location. Select one: A. DAMP B. DRY C. WET
How did you find the angles? Also my computer says the answer to (a.) is incorrect.
Please box the final answers... Thankssss