A transistor is used as a switch and the waveforms are shown below. The parameters are given as follows: VcC 1.6 us, ts 3 ps, t; = 4 us, t, = 100 V, VBE(sat) = 4 V, IBs = 10 A, VCE(sat) = 2 V, Ics = 50 A, ta = 0.4 ps, t, 38us, to = 53 us and f, =10 kHz, k = 40 % and ICFO = 2 mA. The average power loss in the transistor due to the base current are equal to: 1B Is VBE T= 1/f, VBECat)

A transistor is used as a switch and the waveforms are shown below. The parameters are given as follows: VcC 1.6 us, ts 3 ps, t; = 4 us, t, = 100 V, VBE(sat) = 4 V, IBs = 10 A, VCE(sat) = 2 V, Ics = 50 A, ta = 0.4 ps, t, 38us, to = 53 us and f, =10 kHz, k = 40 % and ICFO = 2 mA. The average power loss in the transistor due to the base current are equal to: 1B Is VBE T= 1/f, VBECat)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Microcontrollers (Microprocessor design exercise Digital Voltmeter ) For the following analogue to digital converter case, calculate both the binary and decimal output code. (i) An input voltage of 3.293 V into a 8-bit ADC with a 0 – 10 V input range.
(b)ln a large battery-storage system, the rated output voltage of a battery string is 650V (dc) and the rated current is 1200 A. The voltage can vary in a range from 500V to 800 V. This output voltage is boosted to 900V (dc), as an input to an inverter that interfaces with the three-phase utility grid. A DC-DC converter with a bi-directional power capability is used. The switching frequency is selected to be 50 kHz, and the inductor value is selected such that the peak-to-peak ripple in the inductor current is less than 10% of the rated battery current, with the battery voltage at its rated value. Calculate: i. the inductance value. ii. the peak-to-peak ripple in the inductor current if operating at the rated current but the battery voltage is at its minimum.
Ans
The transistor has a β = 300. The transistor is? A. A switch B. In active region C. In cut-off region D. In saturation region
A fixed bias n-channel JFET with Vdd= 12V, Rd= 1.2k ohms. Idss=12mA and Vp=-4V. Determine Id. a.around 2 mA b.None of these c.around 4.6 mA d.around 3.25 mA
For the BJT circuit shown in Figure b, find the operation point of the transistor. (use B=100 for BJT) Rc 9 k2 Vcc= 2.5 V Rp1 k2 Maximum file size: 51 Files
For the transistor circuit a. what is VCE when VIN =0 V? b. What minimum value of IR is required to saturate this transistor if ßpc is 200? Neglect VCE(sat)- c. Calculate the maximum value of Rp when VIN = 5 V. Vcc +10 V Rc 1.0 kN VOUT Rg VIN
Using the re model circuit, determine the total voltage gain for the BJT circuit shown below. Show the details of your work. 22V ... 5.6k0 330k Vo + 10UF-POL B = 80 1200 10UF-POL To = 40 kN 2N2221 6.8k) Vs 4700 22UF-POL
Given zener voltage at 9V, input voltage at 12Vdc to 15Vdc and ILmax at 40mA. What is Rsmin if Izmax rated is 50mA?
Q1- Determine the fundamental period of the signal a- x(t) = 2cos(10t+ 1) - sin(4t -1). B- x(t) = 3 cos (2t+ π/10)
Q/B For the circuit below, RE=2K ohm, RC=3K ohm, VEE=4 Volt, Vcc=20Volt. Assume the transistor to be silicon. Find: Ic RE VEE IC ------ A 0.00165 0.165 1.65 0.0165 VCB= ------- Volt 150.5 1.505 0.15 15.05 Rc Vcc
From the circuit, a. What is VCE when VIN = 0b. What minimum value of IB will saturate the transistorc. Calculate the maximum value of RB when the input voltage is 5V.Please explain the steps.