A transistor amplifier which uses a npn BJT and various passive components is shown in Figure Q2. A table of component values is shown in Table Q2. Calculate the voltage at the collector emitter junction VCE- -- 4 +Vcc R1 Vout Vin R2 R3 Figure Q2 R1 = R2 = 50 kQ R3 = 5 kQ +Vcc = 15 V Q1: B = 200 VBE(dc) = 0.7 V VT = 25 mV Table of Component values and Transistor Parameters Table Q2 O 8.2V O 0.82V 6.8V 0.68V

A transistor amplifier which uses a npn BJT and various passive components is shown in Figure Q2. A table of component values is shown in Table Q2. Calculate the voltage at the collector emitter junction VCE- -- 4 +Vcc R1 Vout Vin R2 R3 Figure Q2 R1 = R2 = 50 kQ R3 = 5 kQ +Vcc = 15 V Q1: B = 200 VBE(dc) = 0.7 V VT = 25 mV Table of Component values and Transistor Parameters Table Q2 O 8.2V O 0.82V 6.8V 0.68V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Ce301 q4a/b
In a side-transistor circuitThe maximum values are given below. Normalmaximum VCC voltage of the BJT under conditionscalculate.PD(max)=52/100W
Determine the folowing A.base current (IB), B. collector current (Ic), C. collector-to-emitter voltage (VCE),D. draw the load line, locate the Q-pointF. input impedance (Zi),G. Output impedance (Zo)
Example 8:-
Using the re model circuit, determine the total voltage gain for the BJT circuit shown below. Show the details of your work. 22V ... 5.6k0 330k Vo + 10UF-POL B = 80 1200 10UF-POL To = 40 kN 2N2221 6.8k) Vs 4700 22UF-POL
Q10. Determine maximum and minimum value of Zener current if value of series resistance is 1 K, load resistance is 2KN and input varies from 10V to 30V. Zener voltage is 5 V. I
Suppose you have an BJT with alpha dc equals 0.95 . The DC current gain ( beta dc) will equal :
Q10. Determine maximum and minimum value of Zener current if value of series resistance is 1 K, load resistance is 2KN and input varies from 10V to 30V. Zener voltage is 5 V.
8.
Q4. For the circuit shown in Figure Q4: i) What is the type of MOSFET and the amplifier configuration? ii) Find the Q-point (Ip and Vps) iii) What is the device transconductance, gm? iv) What are the voltage gain and output voltage? v) Draw the input /output voltage waveforms showing the phase relationship between them. Be sure to label them properly. +20V IDON = 15 mA@ VcsON = 6V VGSTH = 1V 1kQ Rp C2 10M2 Ro1 out Vin 3.3MQ Ra, 47003 Rs 50mV Figure Q4
A. Determine the VCE transfer as a function of Vi of the circuit in figure 1, (eliminating the zener diode), indicating the different areas of the transistor (Active zone VBE = 0.7v, VCEsaturation = 0.2v, VBSaturation = 0.8v; saturation zone: The transistor has a B = 110 and the reverse saturation current negligible. B. As in section a) with the zener diode, assuming that this is ideal, whose zener voltage is equal to 3.5Volts. R3=8K, R4=9K
3. In a certain n-channel JFET, Ipss= 8 mA and Vp=-4 V. (a) Determine the value of Ves for maximum drain current. (b) Calculate the drain current for VGs=-5 V (c) Calculate the drain current for Ves=-2 V (d) Determine the maximum value of VGs for cut-off condition.