A thyristor half-wave controlled converter has a supply voltage of 240V at 50Hz and a load resistance of 100Ω. Determine the power factor when the firing delay angle is 30°?

Q: Design a square wave generator using OPAMP to have output frequency of 2.5KHZ with variable duty…

A: The circuit for getting a square-wave at the output is given by:

Q: Firing angle-50 Degree 1:2 -200/200v For the circuit shown the DC ratting current of the Thyristor…

A: Secondary voltage of the transformer, Vs=200*2=400V

Q: A boost converter with an input voltage of 5 V dc and an output voltage of 8 V dc will have a duty…

A: Given a boost converter with, Input voltage, Vs=5 V Output voltage, Vo=8 V Duty cycle, α=?

Q: Single phase full wave controlled converter circuit is powered by a single phase source. When the…

A:

Q: Q/ Why is high frequency (Fsw) used in Buck Converter circuits

A:

Q: Problem: A certain rectifier filter produces a dc output voltage of 75 V with a peak-to-peak ripple…

A: In this question  We need to determine the ripple factor  We know  Ripple factor = ∆V/Vdc  Where ∆V…

Q: The choke of Figure has a d.c. resistance of 25. What is the d.c. voltage if the full-wave signal…

A: Given: Vin(peak)=25.7 volt RC=25 ohm RL=750 ohm

Q: 230V R=20 ohm ms s AC

A: AC-AC converters will control AC power. There are 2 types 1. AC voltage regulator 2. Cycloconverter.…

Q: Design a Buck Converter with the Following Features. Input Voltage = 50 V Output Voltage = 20 V…

A: Buck Converter:  It is a type of DC-DC converter where input voltage is being stepped down to get…

Q: The input voltage of the buck converter should be 100 and the output voltage should be 60. The…

A:

Q: O Inductor Diode Voltage Surce Swilching Device Capactor This DC-to-DC converter has a duty cycle of…

A: Given data: Duty cycle = 33.3% = 0.333 Converter input = 5 V Output voltage = ? The dc-dc…

Q: the ripple current is equal to

A:

Q: A boost converter is 80% efficient, has an output voltage of 12V and a duty cycle of 75%.  What is…

A: Fig in solution shows the basic configuration of a boost converter where the switch is integrated in…

Q: The choke of Figure has a d.c. resistance of 25. What is the d.c. voltage if the full-wave signal…

A: The diodes are made of semiconductor materials. Silicon and germanium are common semiconductors for…

Q: In mode of operation, fully controlled converter will keep a delay angle range between 90° to 180°.

A: In this question, we have to find out in which mode fully controlled converter will keep a delay…

Q: A DC-DC buck converter operates in continuous conduction mode. It has 48 V input voltage, and it…

A: Given- DC-DC buck converter- Input voltage V=48 V, Resistive load R=24 Ω, Frequency f=250 Hz, Switch…

Q: In 3 phase half wave converter the thyristor T1 is reverse biased due to the 'a' phase supply.…

A: The three phase half wave converter have the thyristor T1 in series connection with the load. All…

Q: In Buck/Boost converter of Duty cycle is 50% to 100%, then the output voltage will be     less…

A:

Q: What is the minimum detectable temperature change that the A-to-D converter can resolve

A: The minimum detectable temperature change that the A-to-D converter is given by the expression as…

Q: 6. Determine the hysteresis voltage for each comparator in Figure 13-63. The maximum output levels…

A:

Q: A thyristor half-wave controlled converter has a supply voltage of 240V at 50Hz and a load…

A: Given data, Supply voltage, Vs=240 V Load resistance, RL=100 Ω Delay angle α=300

Q: the way of work buck dc-to-dc converter

A: The operation is explained in following pictures

Q: single phase full controlled bridge converter uses     a. 4 SCRs and 2 diodes b.  4 SCRs   c.…

A: fully controlled converter means it has control over both positive and negative half cycles .  where…

Q: A three phase converter with an ac-side inductance L, of 25 µH and Vµ equal to 470 V at 60 Hz. The…

A: As we have given: VL-L=470 VLs=25 μHPDC=500 kWIDC=530 A Step 1: Calculate output dc voltage…

Q: Assume the following values for an ADC, with a 8-Bit input: Clock Frequency = 2 MHz • VT=0.1 mV FS…

A: We need to tell about the resolution of ADC .

Q: For the clamper circuit shown below, Find and Plot the output waveforms and Check the essential…

A:

Q: The power electronic converter shown in the figure has a single-pole double-throw switch. The pole P…

A: Referring to the given circuit, the output will always be less than the input voltage since, the…

Q: In Boost converter, if the supply voltage is 200 V and the Duty cycle is 50%, the output voltage…

A: It is given that: Supply Voltage=Vs=200 VDuty Cycle=α=50100=0.5

Q: A 80 V rms is stepped down to 18V rms by a transformer. The output from the transformer is rectified…

A:

Q: A step-up chopper is fed with 200 V. The conduction time of the thyristor is 200 us and the required…

A: Step-up chopper- Input voltage Vin=200 V, Conduction time of the thyristor =200 μs. Required output…

Q: Hi, I need your help on the following question: Design an adapter circuit that has the input 120…

A: Adapter circuit is an AC to DC converter that provides constant and regulated output DC voltage.…

Q: In a step-up/step-down converter, Vin=12V, Vioad=15V (regulated), Itoad=250mA, Lmin = 150µH, C =…

A:

Q: For the circuit shown below, find the value of AVO, if duty ratio of switch is 0.4 and it is…

A: The given circuit is buck boost converter- Duty ratio α =0.4, Frequency f=25 kHz. To Find- The…

Q: QUESTION 6 Determine the output waveform in Figure 4 and draw the timing diagram.

A:

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.