(b)A three-phase uncontrolled bridge rectifier is connected to an AC supply of 415Vthrough a delta-star transformer as shown in the Figure. The load consists of largeinductance to render a level load current of 60A at 300V. Assuming voltage dropacross the power device to be 0.7V, compute the following:i)Rms value of secondary phase voltage and current;ii)Rms value of primary phase voltage and current3;iii)Transformer power rating in kVA and transformation ratio;iv)Device ratings.本の。本の本のLoad本の。本。本の。Figure

Given values are - Io=60AVo=300VoltVD=0.7Volt Given circuit is - Given circuit is 3 Phase…

A three-phase uncontrolled bridge rectifier is connected to an AC supply of 415V through a delta-star transformer as shown in the Figure. The load consists of large inductance to render a level load current of 60A at 300V. Assuming voltage drop (b) across the power device to be 0.7V, compute the following: i) Rms value of secondary phase voltage and current; i) Rms value of primary phase voltage and current; iii) Transformer power rating in kVA and transformation ratio; iv) Device ratings. 4 Fo the 本。本の本の Load FL 本の。本の本の Figure

A three-phase uncontrolled bridge rectifier is connected to an AC supply of 415V through a delta-star transformer as shown in the Figure. The load consists of large inductance to render a level load current of 60A at 300V. Assuming voltage drop (b) across the power device to be 0.7V, compute the following: i) Rms value of secondary phase voltage and current; i) Rms value of primary phase voltage and current; iii) Transformer power rating in kVA and transformation ratio; iv) Device ratings. 4 Fo the 本。本の本の Load FL 本の。本の本の Figure

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2
Design a CT-FWR to supply a load of (502) with a waveform of the following specifications: - • Vdc = 12 V • Ripple factor = 0.1 % • the main power supply is (220 Vrms, 50 Hz). Determine the following values: - 1- The value of capacitor filter. 2- The maximum load voltage (VmR) 3- The transformer turns ratio (a). 4- The RMS value of the load voltage. 5- Draw the output waveform. (assume ideal diodes)
2. An RLC circuit is connected across a variable frequency, 110-volt source. When the frequency is varied, the maximum effective (rms) value of the current is 5.6 A and occurs at 45 Hz frequency. At this frequency, the voltage across the capacitor is 200.8 volts. Determine the power factor of the circuit at 60 Hz.
B1. The sinusoidal waveform is displayed by the CRO is shown in Figure below. The 'time/cm switch is on 10 ms/cm and the volts/cm' switch is on 10 V/cm. Calculate (a) the frequency, (b) the peak to peak voltage, (c) the amplitude (d) the r.m.s voltage.: The frequency is = The peak to peak voltage is = The amplitude is = The r.m.s voltage is =
Please solve in 25 minutes, please
3.16 A three-phase, full-wave half-controlled rectifier bridge circuit is operating at a delay angle a = 67° when supplying full power. The per-phase inductance of the coupled transformer is 2 mH. The input voltage has an rms magnitude of 230 V per phase at 50 Hz. The load current in the d.c. side is 15 A at 200 V. It is required to: (a) Obtain the drop in the d.c. voltage due to current overlap. (b) Calculate the rms secondary voltage of the transformer. (c) Calculate the overlap angle. (d) Obtain the recovery angle while the converter in operating in the inversion mode with 15 A, 200 V d.c. input. (e) Obtain the firing angle for the conditions in (d). [Ans: (a) 4.5 V, (b) 450 V, (c) 1.06°, (d) 67.14°, (e) 111.8°]
Construct the circuit in Figure 1 in the Circuit JS simulator. Note that the voltage source is given in RMS. Within Circuit JS while defining the max voltage of the voltage source include “rms” after the number to tell Circuit JS that this is a rms value. Also note that there are additional parameters when instantiating a transformer in Circuit JS. Leave these at the default values. Additionally, transformers may have problems simulating in Circuit JS. Answer the following: 1. From the simulation results, determine the power dissipated in R2 and compare to the expected value from the previous section.2. Change the transformer ratio (“Ratio” as a fraction when you “Edit…” the transformer component) to the value calculated in the previous section to provide maximum power transfer in R2. Note: In Circuit JS, Transformer Ratio = Primary/Secondary.3. Rerun the simulation, calculate the power dissipated in R2 and compare to the expected value from the previous section.4. Change the…
is de (c) -Idc de 0 first 2 harmonics of b If ripple-free load current in steady-state is assumed, the input current is waveform of the single-phase full-wave rectifier may then be depicted as shown in the figure above for an ideal input transformer. With the assumption that the supply is ideal and perfectly smooth and ripple free load current, which implies an infinitely large load inductance, it is quite straightforward to obtain an analytical expression for the input current harmonics. The rectangular wave is defined as Ide K f(t)= By using the full range Fourier Series, compute the de when 0
The sinusoidal waveform displayed by the CRO is shown in Figure below. The 'time/cm' switch is on 50 ms/cm and the 'volts/cm' switch is on 1 V/cm. Calculate (a) the frequency, (b) the peak to peak voltage (c) the average voltage (d) the r.m.s voltage.
I need the answer quickly
The ripple factor for pure dc is
Q3) A 3-phase half-wave controlled supplies a resistive load of 100 Q from a 380V, 50 Hz supply. Calculate the average load voltage, the average load power, the operating power factor and the voltage ripple factor for trigger angles of 45° and 90°.