A three phase six-step inverter is producing an output voltage with VL=200V at 52HZ. The load isa Y-connected ac motor which is modeled by as 100mH inductor/phase in series with 10Ohms resistor.2996iloVJuqtuUOCalculate the fundamental component of the load currentApproximate the current harmonic distortion to all current harmonics of order 10 and below, determine theharmonics distortion of the output current

Given thatVLL=200vf=52HzL=100mHR=100Ω

*:A three phase six-step inverter is producing an output voltage with VLL=200V at 52HZ. The lo nnected ac motor which is modeled by as 100mH inductor/phase in series with 100hms resistor. 2996iloVJuqtuC late the fundamental component of the load current kimate the current harmonic distortion to all current harmonics of order 10 and below, determine the nics distortion of the output current

*:A three phase six-step inverter is producing an output voltage with VLL=200V at 52HZ. The lo nnected ac motor which is modeled by as 100mH inductor/phase in series with 100hms resistor. 2996iloVJuqtuC late the fundamental component of the load current kimate the current harmonic distortion to all current harmonics of order 10 and below, determine the nics distortion of the output current

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Draw circuit and Explain working of Single-Phase inverter with RL load.
Q5: A three-phase bridge inverter shown in Figure (4), feeds a balanced star-connected load (R)= 20 Q with a DC source (E)-400 V. Find the RMS value of load voltages and currents, the current flow in each transistor, Pr, and im. Draw i, is, i Va. V, Ve, and in. Assume that: 1) The conduction angle of each switch is 180°. 2) No base current delivered to T3 due to a bad connection. T3 T5 RI R3 T4 T6 T2 Figure (4)
A three-phase, fully controlled thyristor bridge converter is used as line commutated inverter to feed 50 kW power at 420V de to a three-phase, 415 V (line), 50 Hz ac mains. Consider de link current to be constant. The rms current of the thyristor is
for square wave PWM inverter, Vdc=100V, L=25mH, R=1002, f=60Hz. draw the spectrum of the output voltage and current and then find the rms current value and the output power. Take n =1-20.
A 1-phase full-bridge inverter is connected to a load of 4.2 . The DC input voltage is 40 V. What is the rms output at fundamental frequency?
A single-phase, half-bridge inverter feeds a resistive load, R = 10 Ohms. If the source voltage is 240 V, determine (a) the RMS value of fundamental component of output voltage, (b) the output power, (c) the peak off-state voltage across each semiconductor switch, (d) the lowest-order harmonic and the corresponding harmonic factor, and (e) the RMS and average values of currents through semiconductor switches o 9:22
What is the relation between the injected AC real power and the power factor of the inverter?
#4 the input voltage of a three phase inverter is 600Vdc, what is the duty cycle for phase a as a function of time to generate 270cos(ot)V phase voltage? #5 how to generate 460V 400HZ three phase voltages from 460V 60HZ three phase voltage?
Power electronics
Q.2 A bipolar PWM single-phase full-bridge DC/AC inverter has Va = 300V, ma = 1.0, and ftri = 2550 Hz. The inverter is used to feed RL load with R = 100 and L = 15mH at fundamental frequency is 50 Hz. Determine: a) The rms value of the fundamental frequency load voltage and current? b) The highest current harmonic (one harmonic)? c) An additional inductor to be added so that the highest current harmonic is 10% of its in part b?