H.W.2:A Three-phase, 400 V, 50 H2. Stor Cennected SCIM,The motor dvaws no-lond C.rent of (5A) withno-lond observedpowerof (1120 w). At Plload Condidion the moter drans (18 A) at(0.85) powerAvmature resistamce is (o.6 slph), and therodational losses (250 w), Determine!factor and (o.04) Slip. if theO Ivon lossO Output power

Given VL =400 V, IL=18 A, P.F. 0.85, slip 0.04, Ra=0.6 ohm/pH, rotational loss = 250 W

A Three-phase, 400 V, 50 H2. Star Connected St The mator dvaws no-load Caret of (5A) with no-lond observed power of (1120 w). At Pll load Condidron the moter draws (18 A) at (o.85) pomer facka and (o.04) Slip if the Avmature resistance is (0.6 slph), and the rodational losses (250 w), Determine! O Ivon loss O Output power

A Three-phase, 400 V, 50 H2. Star Connected St The mator dvaws no-load Caret of (5A) with no-lond observed power of (1120 w). At Pll load Condidron the moter draws (18 A) at (o.85) pomer facka and (o.04) Slip if the Avmature resistance is (0.6 slph), and the rodational losses (250 w), Determine! O Ivon loss O Output power

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Power Electronics Question
Q1: Draw the d.c load line for the circuit shown in figure. NO SIGNAL Van Vce= 12.5 V www Re=25 ka
Can you solve the question step by step clearly ?
QUESTION 2 Given is a voltage regulator with a nominal output voltage Vo=11V. When the load current varies between 0.1A and 5A, the output voltage varies between 10.8V and 11V. - Determine the load regulation in percent, write the answer without the unit.
5. For the transformer coupled half- wave rectifier circuit shown below: detei peak secondary voltage of the transformer 4:1 120V, 60H3 R. 2.5KL
Q2) Design a Bridge FWR to supply a load of (1002) with the waveform shown in figure from the main power supply of (220 Vrms). Find: - 1- The transformer turns ratio (a). 2- The ripple voltage. Vot Vm = 12 V 3- The Vde value. 4- The RMS value of the output voltage. 5- The ripple factor. 6- The value of capacitor filter. Vip = 0.1 V (assume ideal diodes) T=0.01 sec. tisec) Q3) V in Design a regulated circuit to supply a constant voltage of (10 V) across a resistive load of (50 2). The input voltage is shown in the figure. The minimum current for the Zener diode operation is (Izk=5mA). Find the 15 V 15 maximum power dissipated in the Zener diode. 12.5 12 V 10
give an example of AC to DC converter diagram
1- spark gaps testing method is applicable for testing 2- the electrical circuit that we use to measure high voltages and is not affected by frequency change 3- We can say high voltages if exceed ------------ V (Alternating voltages) 4- Transient voltages which are caused over voltages be in two forms 5- High voltages can be generated for testing in three ways ------
The resistance increases as temperature rises usually due to increased thermal lattice agitations is a. RTD b. PTC c. NTC d. EMF
Dc converter
B1. For the CRO square voltage waveform is shown in Figure. The 'time/cm' switch is on 5 ms/cm and the 'volts/cm' switch is on 10 V/cm. Calculate (a) the frequency, (b) the magnitude of voltage, (c) the peak voltage, (d) the R.M.S voltage. The frequency The magnitude of voltage The peak voltage The R.M.S voltage