A three-cylinder single acting engine has its cranks set equally at 120° and it runs at 1200 r.p.m. The torque-crank angle diagram for each cycle is a triangle for the power stroke with a maximum torque of 90 N-m at 60" from dead center of corresponding crank. The torque on the return stroke is sensibly zero. Determine: • Power developed. • Coefficient of fluctuation of speed, if the mass of the flywheel is 6 kg and has a radius of gyration of 80 mm. • Coefficient of fluctuation of energy. Maximum angular acceleration of the flywheel.

A three-cylinder single acting engine has its cranks set equally at 120° and it runs at 1200 r.p.m. The torque-crank angle diagram for each cycle is a triangle for the power stroke with a maximum torque of 90 N-m at 60" from dead center of corresponding crank. The torque on the return stroke is sensibly zero. Determine: • Power developed. • Coefficient of fluctuation of speed, if the mass of the flywheel is 6 kg and has a radius of gyration of 80 mm. • Coefficient of fluctuation of energy. Maximum angular acceleration of the flywheel.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A belt conveyor transports 18 tonnes per hr at 20°. Determine the speed reducer power factor to lift the load vertically up sufficient to give 33.5 m horizontal center-to-center pulley distance. 1750-rpm motor, plain chain drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley. No tripper.
What is the power (?) lost to main crankshaft friction in a four-cylinder engine with a 100mmbore and stroke if the engine is operating at 1500 rpm? Assume the main crankshafthas five bearings, each with a diameter of 50 mm and length of 25 mm.
2) An electric motor transmits 0.5HP at 1600RPM. A 100 tooth helical pinion having a normal pressure angle of 25° and a helix angle of 15° and a normal diametral pitch of 10 teeth/in transmits power to a 100 tooth gear. Determine the tangential, radial and axial forces on the gear tooth.
Fast please ?
Example. Design a plain carbon steel Centre crankshaft for a single acting four stroke single cylinder engine for the following data: Bore=400 mm; Stroke = 600 mm; Engine speed = 200 r.p.m.; Mean effective pressure = 0.5 N/mm²; Maximum combustion pressure = 2.5 N/mm²; Weight of flywheel used as a pulley = 50 kN; Total belt pull = 6.5 kN. When the crank has turned through 35° from the top dead centre, the pressure on the piston is IN/mm² and the torque on the crank is maximum. The ratio of the connecting rod length to the crank radius is 5. Assume any other data required for the design.
Torsian in a Bolid wY Awollow tube The figure above shows a rig which is used to find the angle of twist for a shaft. A torque is applied to the shaft by applying a force to the torque arm, as shov on the right hand side of the figure above. Given Load applied to end of torque arm = 90 N Length of torque moment arm = 150 mm Length of shaft(L) = 300 mm Young's modulus of steel = 205 kN/mm22 Modulus of rigidity 84 kN/mm22 Solid shaft diameter = 15 mm
5. What do you understand by 'fluctuation of energy' and 'maximum fluctuation of energy'. 6. Define 'coefficient of fluctuation of energy'. 7. Discuss the various types of stresses induced in a flywheel rim. 8. Explain the procedure for determining the size and mass of a flywheel with the help of a turning moment diagram.
i need the answer quickly
2. Try to design a single reducer with a cylindered worm gear drive. Given the rated power of electric motor P=7.5KW, rotational speed n=1440r/min, speed ratio i=24(for reducing applications), uniform driven load, life expectancy 10 years, 16 hours per day, under unidirectional operating condition.
The 24T 6-pitch 20° pinion 2 shown in the figure rotates clockwise at 900 rev/min and is driven at a power of 28 hp. Gears 4, 5, and 6 have 24, 36, and 144 teeth, respectively. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Fixed What torque can arm 3 deliver to its output shaft? The torque that arm 3 delivers to its output shaft is lbf-in.
A mini motorcycle is driven by a combustion engine with mechanical transmission. The 12Hp motor spins at a speed of 1150 rpm. The motorcycle runs at a linear speed of 45 km/h on 12-inch wheels. Preliminary center to center distance is 13”. This type of motorcycle requires two strands (conical double sleeve assembly) and is subjected to hard shocks. a) Calculate the effective power.b) Choice of chain and sprocket. (Standard part number, see catalog)c) Calculate the speed ratio. https://pdf.directindustry.com/pdf/martin-sprocket-gear/general-catalog/9091-246439.html
QUESTION 10 A motor-cycle engine crankshaft has an angular velocity of 523.6 rad/s and is in third gear of ratio 1.62:1. The final chain reduction is 4.7:1 and the effective wheel diameter 0.73 m. Calculate the road speed of the machine in km/h.