A thin square plate PQRS is symmetrically deformed into the shape shown by the dashed lines in the figure. Assume d = 255 mm, d₁=256.1 mm, and d₂ = 253.6 mm. For the deformed plate, determine (a) the normal strain of diagonal QS. (b) the shear strain Yxy at corner P. d₂ Q d d₁ Undeformed Calculate the deformation of diagonal QS. Answer: dos = 9810.3 -Deformed mm

A thin square plate PQRS is symmetrically deformed into the shape shown by the dashed lines in the figure. Assume d = 255 mm, d₁=256.1 mm, and d₂ = 253.6 mm. For the deformed plate, determine (a) the normal strain of diagonal QS. (b) the shear strain Yxy at corner P. d₂ Q d d₁ Undeformed Calculate the deformation of diagonal QS. Answer: dos = 9810.3 -Deformed mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

material with a rectangular cross-section of 4 mm by 25 mm is loaded in tension with a force of 32 kN. A strain gauge bonded to the material measures a strain of 400 microstrain when the sample is loaded. culate Young's modulus of the material, measured to the nearest GPa (GN/m2) and enter your answer in the box below. ung's modulus: [ GPa
P
A strain gage is mounted to the outer surface of a thin-walled boiler. The boiler has an inside diameter of 1820_mm and a wall thickness of 18 mm, and it is made of stainless steel [E = 179 GPa; v = 0.3]. Determine: (a) the internal pressure in the boiler when the strain gage reads 210 µɛ. (b) the maximum shear strain in the plane of the boiler wall. (c) the absolute maximum shear strain on the outer surface of the boiler. Answers: (a) p = i MPа. (b) Ymax in-plane = i prad. (c) Yabs max i prad. =
(b) A differential element on the bracket as shown in Figure Q1 is subjected to plane strain that has the following components: ex = 150µ, ey = 200μ , γχν = -700μ. By using the strain transformation equations, determine:- The equivalent in-plane strains on an element oriented at an angle 0 = 60° counterclockwise from the original position. (ii) Sketch the deformed element within the x' – y' plane due to these strains. (iii) The stresses on the oriented planes in (i) where the value of elasticity, E = 200 GPa and Poisson's ratio, v = 0.32. (iv) Give your comments on those stresses in (iii) in terms of elastic limit/failure if the material's yield strength in tension/compression is 250 MPa and in shear is 90 MPa.
The piece of plastic is originally rectangular. Suppose that aaa = 270 mmmm and bbb = 440 mmmm . (Figure 1) Figure 1 of 1 Part A Determine the magnitude of the shear strain γxyγxy at corner DD if the plastic distorts as shown by the dashed lines
3.3 A steel wire of length L = 20 cm is subjected to nonuniform heating such that the exten- sional strain is £x=k(x/L), where k= 2 x 102 and x is the distance of a point from one end of the wire. Find the length of the deformed wire. Ans: 20.1 cm.
Two [0°, 45°, 90°] strain gauge rosettes are placed along the neutral axis of a 4-point bent beam as shown in the figure below. What will the strain reading in each of the 6 gauges be? P L/3 L/3 -45° 45 L/4 L/2 L NA h
2. The stress-strain behavior of a ductile cast iron of diameter 15.8mm and a gauge length of 60.80mm is shown below, 400 300 200 100 0.00 0.10 Strain Determine the following: (a) the modulus of elasticity (b) yield strength at a strain offset of 0.002. Stress (MPa)
Q4
Please show each and every step in detail. Dont miss any steps and highlight the final answer. Thanks!
C1=150 C2=110
The rigid beam is supported by a pin at A and wires BD and CE. Figure 3 m 2m 1 of 1 4 m ▾ Part A If the load P on the beam causes the end C to be displaced 8 mm downward, determine the normal strain developed in wire CE. (Figure 1) ECE = Submit ▾ Part B EBD = Submit V—| ΑΣΦ Determine the normal strain developed in wire BD. Provide Feedback Request Answer ΑΣΦ vec Request Answer vec SO ? ? mm/mm mm/mm Next >