A thin rectangular plate of dimensions 100 mm x 250 mm is formed by welding two triangular plates. The plate is subjected to a compressive stress of 2.5 MPa in longitudinal direction and a tensile stress of 12 .0 MPa in the transverse direction. Determine the normal stress ow acting perpendicular to the line of the weld and the shear stress Tw acting parallel to the weld. 12.0 MPa Weld -250 mm- 100 mm 2.5 MPa

A thin rectangular plate of dimensions 100 mm x 250 mm is formed by welding two triangular plates. The plate is subjected to a compressive stress of 2.5 MPa in longitudinal direction and a tensile stress of 12 .0 MPa in the transverse direction. Determine the normal stress ow acting perpendicular to the line of the weld and the shear stress Tw acting parallel to the weld. 12.0 MPa Weld -250 mm- 100 mm 2.5 MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 2. point J, what is the maxXimum shear stress the weld has to with- K 700 mm F=3kN Txy C2
strictly don't copy the answer
A 1/4 in fillet weld is to transmit a total force of 12,000 lb. If the allowable unit stress in shear on the weld is 15,800 psi, the minimum effective length of the weld must be A. 5.4 B 4.9 in C. 4.3 in D 3.9 in.
Two aluminum plates, each having a width of b = 8.0 in. and a thickness of t = 0.750 in., are welded together as shown. Assume a = 4.0 in. For a load of P = 75 kips, determine (a) the normal stress that acts perpendicular to the weld and (b) the magnitude of the shear stress that acts parallel to the weld. Answer: O= P T = 1 i 1 ksi ksi b P
At room temperature (20°C), a 0.5-mm gap exists between the ends of the rods shown. The temperature eventually reaches a value of 140°C. Determine the normal stress in the aluminum rod. Determine the change in length of the aluminum rod.
A state of stress at a point A is given by σx = -75 MPa, σy = 122 MPa, and τxy = -3.75 MPa. Which of the following is one of the principal stresses for the point A.
How many 10-mm diameter rivets is needed to fasten member BF to the gusset plate at B if the member BF has thickness of 8 mm and the working stresses are 30 MPa for shear in the rivets and 45 MPa for bearing due to the rivets.
7m 4 m 4m 4 m 4m 150 kN 100KN 120KN Determine the normal stress in member BC if the section is circular having an outside diameter of 70mm w/ a thickness of 5mm and indicate if the member is in Compression or Tension.
The solid steel rod (1) has an allowable shear stress of 12 ksi. The brass tube (2) has an allowable shear stress of 5 ksi. The diameter of the rod is d1 = 0.625 in. The outside diameter of the tube is D2 = 1.625 in., and its wall thickness is t2 = 0.125 in. The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at B. Determine the largest torque Tmax that can be applied at the upper end of the steel rod.
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 48 in. and a wall thickness of 0.375 in. Determine the largest allowable gage pressure if the allowable shear stress parallel to the weld is 3.10 ksi.
The bolted connection illustrated below comprises one bolt and two plates. The bolt, which has a diameter of 20 mm, is threaded through a 22- mm diameter hole in both plates. The shear stress of the bolt is 78,000 MPa. Based on this information, determine the following What is the largest force F that can be placed on the joint without shearing the bolt? what is the normal stress, at the gross section area, in each plate? what is the normal stress, at the net section area, in each plate? what is the bearing (or contact) stress between the bolt and each plate?
A 40mm thick steel bar that is fabricated by welding two parts together is shown below. Being concerned for the strength of the weld, you need to find the state of stress (normal stress and shear stress) in the plane of the weld for an applied load of 400kN. Draw your result on a stress element. 57° 400 kN 400 kN 100 mm