H4. A-thin-composite rim of steel and copper rotates about its axis at a constantspeed of 2000 rpm as shown in Fig Q8.Steel Ring18 mm18 mmCopper Ring720 mmFig Q8Calculate the circumferential stress induced in both rings.Note: Modulus of Elasticity for steel = 200 GN/m²Modulus of Elasticity for copper 100 GN/m²Density for steel - 7800 kg/m³Density for copper = 8900 kg/m³

Answered: Image /qna-images/answer/81ba83aa-6360-42e1-883c-b1bc300158c2.jpg

Answered: A-thin-composite rim of steel and…

A-thin-composite rim of steel and copper rotates about its axis at a constant speed of 2000 rpm as shown in Fig Q8. 18 mm. Steel Ring 18 mm Copper Ring 720 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The armature shaft of a 50 kW, 580 rpm electric motor, mounted on two bearings A and B, is shown in Fig. The total magnetic pull on the armature is 5 kN and it can be assumed to be uniformly distributed over a length of 400 mm midway between the bearings. The shaft is made of steel with an ultimate tensile strength of 770 N/mm? and yield strength of 580 N/mm?. Determine the shaft diameter using the ASME code if, k = 1.5 and k, = 1.0 Assume that the pulley is keyed to the shaft. 150 400 10 N/mm 150 300 1000 N 3000 N
A mechanism used in a punchingmachinery consists of a tension spring assembled with a preload of 30 N. The wire diameter of spring is 2 mm with a spring index of 7. The spring has 10active coils. The spring wire is hard drawn and oil tempered having the following material properties:Design shear stress = 780 MPa Modulus of rigidity = 80 kN/mm2Identify (a) the initial torsional shear stress in the wire, (b) the spring rate, and (c) the force to cause the body of the spring to reach its yield strength.
A mechanism used in printing machinery consists of a tension spring assembled with a preload of 40 N. The mean diameter of the coilis 32 mm with a spring index of 8. The spring has 18 active coils. The spring wire is hard drawn and oil tempered having the following material properties: a.Design shear stress = 700 MPb b. .Modulus of rigidity = 80 kN/mm2 Identify (a) the initial torsional shear stress in the wire, (b) the spring rate, and (c) the force to cause the body of the spring to reach its yield strength.
A shaft made of steel receives 7.5 kW power at 1500 r.p.m. A pulley mounted on the shaft as shown in Fig. has ratio of belt tensions 4. The gear forces are as follows : F, = 1590 N; F, = 580 N Pulley Gear F1 A D F, -100 : 200- 100→ All dimensions in mm. Design the shaft diameter by maximum shear stress theory. The shaft material has the following properties : Ultimate tensile strength = 720 MPa; Yield strength = 380 MPa; Factor of safety = 1.5.
3:35 PM Wed Dec 15 7 51% A power transmission shaft is to carry a steady 30 horsepower while rotating at 1000 rpm. Specify a suitable diameter for the solid circular shaft if it is to be made from AISI 1020 cold-drawn steel. Use Appendix A-2 for preferred size. 61
The armature shaft of a 50 kW, 580 rpm electric motor, mounted on two bearings A and B, is shown in Fig. The total magnetic pull on the armature is 5 kN and it can be assumed to be uniformly distributed over a length of 400 mm midway between the bearings. The shaft is made of steel with an ultimate tensile strength of 770 N/mm2 and yield strength of 580 N/mm2. Determine the shaft diameter using the ASME code if, kb=1.5 and kt=1.0 Assume that the pulley is keyed to the shaft.
If the allowable stress of a revolving steel is 150 MPa, what is the equivalent angular velocity which will produce such The mean diameter is 440mm. A uniform bar with an area of 0.25 in2 is pulled between two points. The tensile force at a temperature of 21.11°C is 1200 lb. What will be the stress at -17.78°C? At what temperature will the stress be zero? Assume α = 5 × 10-6 in/(in·°F) and E = 29 × 106 psi.
2. Justify the simplification of this problem to only modeling one-eighth of the cross section 3. Construct two-dimensional elements grid (i.e., grid/mesh region), make the correct numbering and labeling of the nodes and elements.
A shaft is supported by two bearings placed1.2 m apart. A pulley of diameter Dc=0. 675 meter is mounted at a distance of 300 mm to the right of left hand bearing and this drives a pulley directly below it with the help of belt having maximum tension of 2.25 kN. Another pulley of diameter Dd= 0.575 meteris placed 200 mm to the left of right hand bearing and is driven with the help of electric motor and belt, which is placed horizontally to the right. The angle of contact for both the pulleys is 180° and u = 0.24. Determine the suitable diameter for a solid shaft, allowing working stress of 63 MPa in tension and 42 MPa in shearfor the material of shaft. Assume that the torque on one pulley is equal to that on the other pulley C A De m B Da m 0.3 m 0.2 m 1.2 m.
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
A solid 2.0 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant. The torque delivered by the shaft is 3300 Ib-in. What horsepower must be delivered to the shaft to maintain a shaft speed of 590 rpm? What is the maximum shear stress developed in the shaft? Answer: P = hp psi Save for Later Attempts: 0 of 1 used Submit Answer
The torsional assembly consists of solid 1.6 in. diameter aluminum [G = 4,000 ksi] segments (1) and (3) and a central solid 2.0 in. diameter bronze [G = 6,500 ksi] segment (2). Segment lengths are L1 = L3 = 32 in. and L2 = 66 in. Concentrated torques of TB = 2T0 and TC = T0 are applied to the assembly at B and C, respectively. If the rotation angle at joint B must not exceed 3.0°, determine:(a) the maximum magnitude of T0 that may be applied to the assembly.(b) the maximum shear stress magnitude in aluminum segments (1) and (3).(c) the maximum shear stress magnitude in bronze segment (2).