A thermostat for a central air system will control both a heating and cooling system. When a target temperature is set on the thermostat by the operator, it will turn on a heat source if the measured room temperature is below that target temperature. It will also turn on a cooling source if the measured room temperature is above the target temperature. a) Please create a combination logic gate using AND, NOT and/or OR logic gates that would simulate the logic gate circuit necessary to produce the same outcome as a thermostat that controls heating and cooling devices. Be sure to properly label and explain your logic gate system.

A thermostat for a central air system will control both a heating and cooling system. When a target temperature is set on the thermostat by the operator, it will turn on a heat source if the measured room temperature is below that target temperature. It will also turn on a cooling source if the measured room temperature is above the target temperature. a) Please create a combination logic gate using AND, NOT and/or OR logic gates that would simulate the logic gate circuit necessary to produce the same outcome as a thermostat that controls heating and cooling devices. Be sure to properly label and explain your logic gate system.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The logic circuit: (From minimum SOP) Number of gates used in the circuit: 2-Input AND gate.. 2-Input OR gate. NOT gate Number of idle gates in the chip: 2-Input AND gate 2-Input OR gate... NOT gute The logic circuit: (From minimum POS) gates gates gates gates gutes Number of gates used in the circuit: 2-Input AND gate 2-Input OR gate... NOT gate Number of idle gates in the chip: 2-Input AND gate... 2-Input OR gate, NOT gate, IC name: IC name: IC name: gates IC name: gates IC name: gates IC name: gates gates gates
LOGIC GATE ( NEED ONLY HANDWRITTEN SOLUTION PLEASE OTHERWISE DOWNVOTE).
The diagram shows a transistor used to interface a logic gate to a lamp for it to be fully lit. Resistance of lamp=80 ohms 9Vo Signal from logic gate Ovo R Logic gate Output 0.2V 3.3V IB V₁ Lamp a) The logic gate outputs 0.3 for logic 0,and 3.3V for logic 1. Complete the table below to show the effect of these signals on the transistor and lamp by: i) Adding the correct voltages to the V1 column ii)writing either 'Off' or On to show the state of the lamp V1(V) same as VB When filly lit the, the lamp passes a current of 100mA. The transistor has a current gain, beta ẞ of 60 b)Calculate the base current, IB. c)Using KVL find the voltage drop across R. Sate of lamp
Given the following pullup circuit A-Design the pulldown circuitry B- What is the logic function implemented by this would be?
Write the Boolean function of the gate circuit that makes the sequence counter (SC) zero. Draw the circuit diagram of the gates and show how the SC is connected to the INR and CLR inputs. (The number of gates should be minimal.)
28)Which of the following elements does not affect how a ladder logic program is developed? A)The type, direct or inverse acting, and active state of the output field devices. B)The choice of normally-open and normally-closed instructions for the PLC program. C)The contact type and active state of the input field devices. D)The requirement for current sinking or sourcing inputs and outputs.
Please show work
Q3) a- Draw the logic diagram for a circuit that will divide the (fCLK) by 16. Use (-ve) edge triggered (J-KFF). b- Calculate the (fcLk) if the fout =(÷) MHz ----
Please answer the question with steps
Question #1 Which logic function does the circuit implement? VHigh Kt VA Vo VB Vc VLOW (i) (A and B) and C (ii) (A or B) and C (iii) A and (B or C) (iv) (A and B) or C (v) A or (B and C) (vi) (A or B) or C
14. Identify each logic gate shown on the given diagrams * E Your answer
Draw the equivalent ladder diagram for the following combinational logic function using light indicator as outputs Explain the working of the drawn logic diagram with the help of logic input output states. A