A- The PV array installed on the roof of a certain building has a rated power (Pmp-STC) of 600 kWp under standard test conditions. 1- Describe how to connect the SUNCECO PV modules that have 305 W, 37.24 Vmpp to construct this array if each ON-Grid inverter used to connect the PV system to the grid has a rating of P kW where P value is the last two digits (from right) of your registration number (i.e. for the student that has a registration number 202112396, P =96). The DC voltage rating at the inverter input is in the range 90 – 550 V if its rating is less than 10 kW, whereas it is in the range 450- 800 V if its rating is more than 10 kW. You have to calculate the number of series panels in each string and number of parallel strings. Draw an overall diagram for this on-grid PV system with all the protection equipment at both DC and AC side. The inverter has dual MPPTS with a rating of 10 A each. You have to include all of the analysis required to finalize your design. You may need to let number of PV modules not connected. 2- Find the real power generation of this PV array at 900 W/m² and 30 °C if the power temperature coefficient of the PV modules is -0.0045 per degree.

A- The PV array installed on the roof of a certain building has a rated power (Pmp-STC) of 600 kWp under standard test conditions. 1- Describe how to connect the SUNCECO PV modules that have 305 W, 37.24 Vmpp to construct this array if each ON-Grid inverter used to connect the PV system to the grid has a rating of P kW where P value is the last two digits (from right) of your registration number (i.e. for the student that has a registration number 202112396, P =96). The DC voltage rating at the inverter input is in the range 90 – 550 V if its rating is less than 10 kW, whereas it is in the range 450- 800 V if its rating is more than 10 kW. You have to calculate the number of series panels in each string and number of parallel strings. Draw an overall diagram for this on-grid PV system with all the protection equipment at both DC and AC side. The inverter has dual MPPTS with a rating of 10 A each. You have to include all of the analysis required to finalize your design. You may need to let number of PV modules not connected. 2- Find the real power generation of this PV array at 900 W/m² and 30 °C if the power temperature coefficient of the PV modules is -0.0045 per degree.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Determine the value of ix and V. 20230° V 60Hz 10 92 ww ΤΗ m 0.1 F 0.5 H V
What is the power factor? 497 V R4 kn C=0.04 µF L,4 H 750 Hz O A. 0.279 B. 0.479 O C. 0.679 O D. 0.879
9. R equivalent 600
Cab=0.04 mF Calculate C the value of its capacity
Determine the value of ix and V. 20230° V 60Hz 10 92 ww ΤΗ m 0.1 F 0.5 H V
si 10 v + si O v - Vo 1.0kn 10 V
If the heat produced is high, then the calorific value is O Low O High O Medium O Very low
R 14V 4V Vin Vout 1.75 3.50 5.25 7.00 -1.75 -3.50 -5.25 -7.00
15 - If an electron has an energy of 2.5 MeV, what is its energy in joules? O A) 4x10-² j O B) 4x10-19 J O C) 4x10-16 J O D) 4x10-13 J E) 4x10-25 J
220 V 50 Hz 5:1 000000000 eeeeeee Virms is 200 £2 230 O 220 O 44 311.13 O
Under dc conditions, find it in Amperes. Give only the numeric value. 60 www 9V (+ 102 www 30 2 H ell
Determine the time response specifications of the system below: