a The allowable tensile stresses af steel is 30Mpa (a) Calculate the min. thicknes. etstell tube. c)Calculate the tangential and longitudinalstresses in the steel tube. Conc. Yus leo00 dam 1.5 steel tube

Q: Find 150Am 120mm V- 100 mm

A: Consider the below diagram,

Q: Consider the equation for angular twist due to torsion. Imagine you are designing a solid round…

A: The angular distortion of an item caused by a couple of twisting torques is known as the angle of…

Q: QI Define five of the following with sketch. 1-Taper turning 2- Light alloys 3- AA2024 4- Rolling 5-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: (b) Compute the internal torque exerted on gear A (TAC), gear C(TcD) and gear D (TDB). (c) Sketch…

A:

Q: y' = -y tan x, y(0) = 2

A:

Q: For the frame shown below, Is supported by pins at C and D. Determine the magnitude of reaction at C…

A: Consider the free body diagram of the member CBA as shown below.

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: 3. both wires is identical at 1.5 meters and both wires are 5 mm in diameter. The steel wire is made…

A:

Q: дл др Os ӘТ S Cp

A: Write the expression at constant enthalpy. dh=Tds+vdP0=Tds+vdP∂s∂ph=-vT

Q: can you resolve and draw the fbd

A: Freebody diagram of the cut section:

Q: LA 5 mm 28 mm ー-ギー - 49 mm 49 mm

A: For triangle, X1= 0 Y1= (1/3)×95= 31.67 mm  A1 = 1/2 × 98× 95 = 4655 mm2 For semi circle, X2 =0 Y2=…

Q: 2.36x178×106 1- 1 0.9x300x368²×30 Prequired 400 (1.18 30)

A: Given Data⇒

Q: solve frist one please

A: The diametral pitch of each gear:center distance of the gears:Velocity ratio:

Q: Q1 The 45° strain rosette is mounted on a surface of the bracket as shown in Figure Q1. The bracket…

A:

Q: y D 1 m FD

A: Given data:     The given load is: FD=100 kN The given angle is: θ=73˚ The distance between the load…

Q: Q.2 A cantilever beam of length / = 5 m, flexural rigidity El in MPa, and mass m = 1950 kg carries…

A:

Q: 28 cm a? 100 cm 30° V 15 cm

A:

Q: 200 mm В

A:

Q: Add the length of all the horizontal pieces. They go left and right.

A:

Q: D raio s.f.D and B.M.

A:

Q: What is the length and wall thickness of the vertical bear

A: For figure 2,  drawing and the type of symbols present

Q: Q1: Find the angle of the force? 250 Ib 110 Ib 25 140 Ibk 40° 90 Ib 170 Ib

A:

Q: As shown, a section of a roller coaster track (Eigure 3) follows the form of y = (2/3)x¹.5 Locate…

A:

Q: Using the method of joints, determine the force in each member of the truss shown. State whether…

A:

Q: So what is the answer? What is y (1)? What is the answer up to two decimal places.

A: y(1) for equation of motion

Q: Given : Mass of Gears A and B = 2.4 kgs Mass of Gear C = 12 kgs Gears A and B's radius of gyration =…

A:

Q: A multi-stage pump, 260 gpm capacity is installed in a well 27 ft below the static water level.…

A: Given data:  The capacity of the pump is given as Q = 260 gpm = 0.579 ft3/sThe total discharge head…

Q: Incorrect please resolve both parta

A: To calculate the surface temperature of the tank when it is passed through water and to calculate…

Q: If a = 9 in., locate the distance to the centroid of the member's cross-sectional area. (Figure 1)…

A: Draw the given diagram.

Q: A piston-cylinder device contains 1.5 kg of steam at 300°C and 0.4 MPa. Steam is cooled at constant…

A:

Q: How did you get the value of "F"

A:

Q: What is the normal force applied to the block?

A:

Q: The point 1/4 of the way from (1,-3, 1) to (7,9, –9) is A. (4,3,-4) O B. (3/2,3,-3/2) OC.…

A: A point's coordinates are a pair of integers that define its precise position on a two-dimensional…

Q: Starting from rest, Block A moves down the inclined plane with velocity given by 3t“, where t is in…

A:

Q: How do you know that it is -1.2? What determines the sign?

A: Given: How do you know that it is -1.2? What determines the sign?

Q: 7 panels at 4 m B C D 4 m A H. 8 kN 8 kN

A:

Q: why is F3 0

A: Hydrostatic Force- A resultant force which acts on a submerged surface due to the pressure loading…

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.