A tension member is composed of two 2 x 10 plates. They are connected to a gusset plate with the gusset plate between the two tension member plates, as shown in Figure P3.4-2. A36 steel and 4-inch-diameter bolts are used. Determine the nominal strength based on the net section. Two plates, each plate 2 in. thick 2" 5" 2" 2" 3" 3" 2"

A tension member is composed of two 2 x 10 plates. They are connected to a gusset plate with the gusset plate between the two tension member plates, as shown in Figure P3.4-2. A36 steel and 4-inch-diameter bolts are used. Determine the nominal strength based on the net section. Two plates, each plate 2 in. thick 2" 5" 2" 2" 3" 3" 2"

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.4.1P

See similar textbooks

Related questions

Q: Determine the nominial moment strenght oF the beam

A: Nominal moment strength: - It is the maximum bending capacity of beam after that beam will fail in…

Q: List and define the 4 steps of the "4-step travel demand model" used in transportation planning.

A: 12) 4 STEP TRAVEL DEMAND MODEL:

Q: Compute the magnitude of the resultant force on the indicated area and the location of the centre of…

Q: Suppose that a horizontal curve on a two-lane two-way highway has a radius of 200.000m. The lane…

A: Given Data : Radius of curve (R)= 200m Lane width (w) = 3.3m SSD = 120m

Q: so that th

A: solution of problem is below:

Q: Determine the shear stress (in Mpa) in the 30.97-mm-diameter pin at B that support the beam if P =…

Q: A total station instrument occupies control point 20 and takes a BS to CP 22. The Azimuth from 20 -…

A: The backsight of CP-20 to 22 = 215°55'00'' Easting and northing of CP-20 = 8000,13000 The included…

Q: Directions: Answer all questions. Give complete solutions and show all work including units. If…

Q: a) The principal planes b) The principal stresses c) The stress components exerted on the element…

A: Question is based on the element subjected to axial, compression and shear stress . Magnitude of…

Q: Rigid bar ABC is supported by pin-connected bar (1). Bar (1) is 2.0-in. wide, 1.00-in. thick, and…

A: Given: The width of the bar is 2 in. The thickness of the bar is 1 in. The modulus of elasticity of…

Q: Calculate the effective stress at A. Sand 25 m Water Table and- Gravel Unit Weight (y) = 20.72 kN/m…

A: Following is the given soil profile:

Q: 1. Name the direct measurement and indirect measurement rock and fluid properties. 2. Explain…

A: As per our policy the solutions of only first question is provide, for the answers of other…

Q: Problem: Example: Given the following data of a stream of uniform flow: h h=height of water = 1.20m…

A: step 1-

Q: 8. A boat has the cross section shown in Figure 7(a). Its geometry at the water line is shown in top…

Q: A spherical ball of volume 106mm³ is subjected to a hydrostatic pressure of 90 kN/m². If the bulk…

A: Given- Volume of spherical ball V=106 mm3 Hydrostatic pressure P=90 kN/m2 Bulk modulus K=180 MPa It…

Q: Determine the reactions at the supports. 3m m 800 N/m 3 m-

A: Given data:-

Q: Evaluate all distribution factors and carry-over factors associated with joints B and D, and fixed…

Q: 7. A differential leveling loop is run from an established BM to a point 9.66 Km away, with a…

A: Find the order of leveling?

Q: Use moment distribution method to find the moments in each support if El is constant and support A…

A: There wont be any sway as the structure is symmetric according to geometric and loading criteria.

Q: The Howe roof truss shown in figure below carried the given loads. The wind loads are perpendicular…

A: A Howe truss is a type of truss bridge that consists of chords, verticals, and diagonals with…

Q: Q) Work out the canal full-supply levels (FSL) starting from the field with a minimum head of 15 cm…

Q: Imagine a two lane highway segment with crown slopes of-1.3% and the start of the tangent runout at…

A: Given: R=408 mv=71 km/hr×10003600=19.72 m/s

Q: How do I solve this? I'm so confused.

A: Scenario 1: keep the crate in position

Q: If the utility function has been estimated to be: Ux = Ag – 0.04 Ta – 0.05 Tw – 0.02 T, – 0.01 C…

A: Unity function, Ak=0.005Uk=Ak-0.04Ta-0.05Tw-0.02Tr-0.01C Probability of using a given modal:…

Q: A force F is applied to the upper end of the curved wrench, as shown in the diagram. If a = 11.3…

A: The moment about a point is the product of the force and the perpendicular distance between force…

Q: Laboratory compaction test results on a clayey soil are listed in the table below. Moisture content…

Q: Using Method of Joints, determine and tabulate all the bar forces. State whether the member is in…

Q: 1. Use Castigliano's second theorem to determine the horizontal and vertical componen of the…

Q: A particle moves along the x-axis with an initial velocity vx 50 ft/sec at the origin when t= 0. For…

Q: 8) Suppose a new sign structure is being installed on the right side of the EB direction of a…

A: For the value of ADT ≤ 750 The equations for upstream and downstream length of need are as follows:…

Q: 4. Find the tension T, in the rope shown in figure. А. 83.2 N B. 45.8 N C. 70.7 N D. 50 N 45° T2 B…

Q: Determine el momento de inercia, con respecto al eje centroidal (EC) paralelo al ej b = 159 mm, d =…

Q: Calculate the effective stress at A. 25 m Sand and- Gravel Water Table Unit Weight (y) = 20.72 kN/m?…

A: Following is the given soil profile:

Q: How do I solve this? I'm confused.

A: Divide the shape into two parts and calculate the areas. The total area is calculated as,

Q: Determine the allowable ultimate axial load on a rectangular short tied column 12 by 18 in. (300 by…

A: Given: Column dimension = 300 x 450 mm Number of reinforcement bars = 6 Diameter of reinforcement…

Q: With Cartisian coordinates, express a force vector F, where 01 = 45°, c = 3, d = 4, and F 420 N.

Question

Can you solve this for me?

A tension member is composed of two 2 x 10 plates. They are connected
to a gusset plate with the gusset plate between the two tension member
plates, as shown in Figure P3.4-2. A36 steel and 4-inch-diameter bolts
are used. Determine the nominal strength based on the net section.
Two plates, each
plate 2 in. thick
2"
5"
2"
2"
3"
3"
2"

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Trending now

This is a popular solution!

Step by step

Solved in 6 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
Asap pls
The tension member shown in Figure below is a PL 1⁄2 × 8 of A36 steel. The member is connected to a gusset plate with-11⁄8 inch-diameter bolts. It is subjected to the dead and live loads shown. Does this member have enough strength? Assume that Ae = 0.85 An
3. A plate with width of 300mm and thickness of 20mm is to be connected to two plates of the same width with half the thickness by 24mm diameter bolts, as shown. The rivet holes have a diameter of 2mm larger than the rivet diameter. The plate is A36 steel with yield strength F,-248MPa and ultimate strength F,-400MPa. a. Determine the design strength of the section. b. Determine the allowable strength of the section 24mm 30mm
A 16 mm thick tension member is connected by two 6.25 mm spliced plates as shown. The tension member carries a service loads of dead load of 110 kN and a live load of 100 kN. 40, 80 , 40 , 40, 80 40 1625 mm 16 mm 1625 mm Fy 248 MPa Fu = 400 MPa Diam. of bolts = 16 mm Fnv = 300 MPa O Determine the nominal strength for one bolt due to shear. O Determine the nominal strength for one bolt due to bearing strength of the connection. ® Determine the number of bolts required for the connection.
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
The tension member is a PL 12 x 6. It is connected to a 38-inch-thick gusset plate with 7/8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16" Use: Consider deformation at the bolt hole 3" PL ... PL ½x 6 12" 24" 24" 12" a. What is the minimum spacing as per AISC code provisions Round your answer to 3 decimal places.
Plate A, PL 16mm x 375mm, is connected to another plate B with 10- 22 mm o bolts as shown. The steel is A36 steel with Fy= 250 MPa and F,= 400 MPa. Assume that plate B has adequate strength. Use ASD. Plate B 375a 75 m 2 75mm Plate A 75 mm 75mm 150 50150 Compute the nominal strength based on yielding in KN.O Determine the allowable tensile strength of Plate A in KN.O Compute the allowable tensile strength at section a-1-2-2-4-c in KN.0
Please have a Given, Find & Solution.Will Thumbs Up. Thank You
S2 6 7 and 8
2.) Compute the tensile capacity for the ½ inch thick plate shown. The bolts are 4 inch diameter high strength bolts. The steel is A36. -Pt 1
Determine the allowable tensile force P which can be appllied to the plates shown. The AISC specifications A36 steel and 20 mm diameter A325 bolts placed in standard holes with threads excluded from the shear plane are used in a bearing in a bearing type connection. Fy = 248 MPa, Fu = 400 MPa, Fv = 206.9 MPa and Fp = 1.5 Fu. P P CIVIZ 12mm 250 mm ENGINEERING - STEEL DESIGN 12mm P P