A tensile specimen of the metal of 100 mm is length stretched to a length 157 mm during the rolling process. If the metal has a flow curve with parameters: K = 850 MPa and strain hardening exponent n 0.30. Determine the average flow stress that the metal has been subjected to during the %3D deformation.

A tensile specimen of the metal of 100 mm is length stretched to a length 157 mm during the rolling process. If the metal has a flow curve with parameters: K = 850 MPa and strain hardening exponent n 0.30. Determine the average flow stress that the metal has been subjected to during the %3D deformation.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 11 in. inner diameter, 0.35 " wall thickness pipe is under a pressure of 2.5 ksi where strain gages installed along axial and circumferential directions register strains of 180 and 900 micro-strains (x10^-6), respectively. A) In a uniaxial test, the pipe's material is observed to yield at a longitudinal strain of 0.1 in/in. Assuming a factor of safety of 2, the pipe can withstand impact energy of _______ lb - in. per foot without suffering permanent deformation. 4.46x106 3.71x106 5.57x106 2.97x106 1.86x106
A copper specimen subjected to the Brinell Hardness Test using hardened steel ball indenter of diameter 12 mm and the indentation diameter 3.87 mm is measured using an optical magnifying lens with a ruler. Draw the Brinell Hardness Test setup neatly and determine the force applied on the specimen. Take Brinell Hardness Number for copper as 807. Calculate: 1-Surface Area of Indentation (in mm2) 2-Applied Force (in N)
Consider an isotropic material subjected to a combined state of biaxial compression and simple shear, as shown in Fig. 2 and described by the stress state σij = -0 T 0 Calculate the von Mises and Tresca yield criteria as a function of σ and 7 and plot the curves in the σ - 7 plane. Calculate the values of o and 7 at which each of the yield functions intersect theo and 7 axes. Note that your answer should not change if o positive or negative. ko T 0 -ko 0 0 0 4X2 TA ko X1 O
For the curve shown below, calculate the energy required to destroy the specimen. Use any method but your solution must include one integration step at least.
When the true strain equals 0.14 and the true stress equals 355 MPa, the tensile test specimen starts to neck. Find the strength coefficient and the strain-hardening exponent in the flow curve equation without knowing any more about the test.
TelkomSA E estion CALCULATIONS 4.1 Using the given pulley radius and the weight values, calculate the torque applied to the specimens. ← 4.2 Calculate the theoretical angle of twist. 4.3 Calculate the experimental angle of twist for the specimen by using the dial gauge readings and the lever distance to where the dial gauge makes contact. 4.4 Calculate the maximum torsional shear stress and compare the values to the shear stress limits of the material and discuss. 4.76% Rod - Experiment T mass. displacement cog 2009 300g 400g soog Torsion of a Diameter of pulley - 180, 4 mm Length of rad 304mm Diameter of rod at Centre Point - [6,7mm). Measure distance of lever - 19,52 mm Aluminum Solid rod. displacement mass 9,11 mm 9,23 mm 2,34 mm Q. 47 mm g s S8 mm 11:57 3 O
Problem 9 only, solve carefully, include the units in every step and draw the diagram. Thanks! What temperature will the rails just touched if steel railroad is 10 m long are laid with clearance of 3 mm at initialtemperature of 15 C. Use k = 11.7 x 10-6 m/m C. Also compute the strain and stress.
A brass specimen is subjected to a Tensile test in a laboratory. The following data obtained are: Length of Specimen = 322 mm; Diameter of Specimen = 10 mm; Yield Stress = 1279 MPa; Ultimate Stress = 2446 N/mm²; Fracture Stress = 1780 MPa; % of Elongation = 49 % % of Reduction in area = 27 %. Determine the elongation at 43 kN, Load at yielding, Maximum load, Load at fracture, Final Length & Final diameter. Take Young's Modulus as 118 GPa.
4
At a larger radius the rate of shear strain is 18 s-1 and the consistency coefficient is 0.6 Pa s. Calculate the shear stress.
For some metal alloy, a true stress 345 MPa (50040 psi) produces a plastic true strain of 0.02. How much will a specimen of this material elongate when a true stress of 418 MPa (60630 psi) is applied if the original length is 500 mm (19.69in) ? Assume a value of 0.22 for the strain- hardening exponent, n
Consider a metal rod with a critical resolved shear stress of 40 MPa for a specific crystallographic plane (hkl). The angle between the normal to the plane and the applied force is 30 degrees, and the angle between the slip direction and the force is 15 degrees. Two force levels of F1 = 75 N and F2 = 40 N is applied. The cross-sectional area of the rod is 1 mm^(2). Will the slip initiate at the two force levels? Select one: a. F1: Yes, F2: No b. F1: No, F2: No OC. F1: Yes, F2: Yes Od. F1: No, F2: Yes