A temperature sensor with linear transfer function is shown in the figure is used in an loT design. (1) Write the linear transfer function (ii) Write the inverse transfer function Output Voltage (mV) Output Voltage vs Temperature 417 399 392 384 380 364 350 348 329 325 316 309 295 284 28 29 30 31 32 33 34 35 36 37 38 39 40 41 Temperature (C)

A temperature sensor with linear transfer function is shown in the figure is used in an loT design. (1) Write the linear transfer function (ii) Write the inverse transfer function Output Voltage (mV) Output Voltage vs Temperature 417 399 392 384 380 364 350 348 329 325 316 309 295 284 28 29 30 31 32 33 34 35 36 37 38 39 40 41 Temperature (C)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the figure shown, if the transconductance gm-1 mA/V, and Rs << Ro The Voltage gain Av is + Vno 20V (Round your answer to the closest answer) 12 kn Ro NERKO OUTPUT SIGNAL ReIMO RE O 4.8 O 54 O 3.2 O 6.5
Question1: Simplify the following block diagram. Obtain the transfer function from R to C for figure 1, and the transfer function from X(s) to Y(s) for figure 2. Question 2: Convert the block diagram of figures I and figure 2 to a signal-flow graph. G R G2 G3 G3 G4 G6 Figure 1: Block Diagram input output Y(s) X(s) 2 Figure 2: Block Diagram
Design with IC ‘555 and a capacitor of 9 uF: Monostable to get signal period=7 Astable to get frequency=2 Constraints: Use any resistor to be between 1K and 50K.
Please show all work, thanks!
Draw the signal flow graph of the following blocke diagram shown in figure and find the transfer function Y(s)/R(s)
4
The circuit in Figure 1 represents the circuit model of an interference path from source vin to the 10 MQ load resistance at vout- C1 C2 1 pF 1000 pF R V in out 10 MQ Figure 1. Interference modeling a) Determine the transfer function H(f) = vou/Vin from vin to vout- b) Determine the output magnitude vout when Vin is a 170V pk sine wave at 60HZ c) Determine the output magnitude vou when vin is a 1V pk sine wave at 1 MHz
Find the Q-point for the p-channel JFET circuit in Figure. Ipss = 10 mA VDD -9 V Rp 1.8 kn RG Rs 10 ΜΩ 390 N - Vcs 7 V (a) (b)
33nF HI +1₁ 27 k H + 10 k 10 k Vo Opamp is 741 with Vcc = 15V and VEE = -15V What is the frequency of oscillation of the Astable Multivibrator circuit. Sketch the Vo and show complete details.
For each of the following statements, decide whether it is true or false: True In LVDT, the net induced voltage is zero when the core is centered between the two secondary winding segments. The stepper motor is a motor that produces rotation through equal angles. In photoresistors, the electrical resistance increased as the light intensity increased. False O
3) With reference to the switching conditions given below develop an appropriate circuitry that can develop output waveforms as given below, Mark in the circuitry the different components as well Periodic Time (T) A +VL 90° 180° 360 450° 540° time 270° -VL VAB VAC VBc VBA VCA VCB VAB VẠC VBc VBA VDC Vpc 30° 90° 150° 210° 270° 330° 390° 450° 510° 570° time 60° Output Voltage Waveform
Figure V 5 ΚΩ 516 1 of 1 20 ΚΩ v. Part A Use the principle of superposition to find vo in the circuit in (Figure 1). Take v = 45 V and i = 4.5 mA. Express your answer to three significant figures and include the appropriate units. Vo = 5.65 Submit V Previous Answers Request Answer X Incorrect; Try Again; 2 attempts remaining