A tapered circular varying from 20 mm to 10 mm is

Q: A hollow steel has an outside diameter of 5in. and it’s inside diameter is 4in. What is the…

A:

Q: Invection-molding process. Columns (3) through (6) below display the measures of diameters for 6…

A:

Q: D = 875 kN L = 1450 kN SECT. 2 SECT.1 Square Tubing Pipe Fy = 290 mPa Do 4.8m So S, = outide…

A: Question is not clear. Please upload the full question so that the understanding in problem may…

Q: X A cylindrical part of diameter "d" is loaded in tension by a load "P" causing a stress: a-P/A. The…

A: Given, Uncertainty in load = ±15% Uncertainty in diameter = ±7.5% Uncertainty in stress = ±15%

Q: A composite section shown in Figure (2) consisted of a rectangular and triangular sections with a…

A:

Q: I. Select an example from the list of each Structural Shapes. Copy the properties such as mass,…

A: Given,  Several structural shapes according to their designation   To find : Example of each…

Q: At a point in a stressed body, the known stresses are o, = 37 MPa (T), oy = 24 MPa (C), o, = 20 MPa…

A:

Q: Between a plate and the body of a bolt, the projected area is equal to the product of the bolt…

A: Given: Between a plate and the body of a bolt, the projected area is equal to

Q: A 4 m long steel plate having a cross section of 27 mm by 368 mm is use as a hanger and subjected to…

A: We have to suppose the lateral and longitudnal direction  then we have to apply the hooks law onto…

Q: Problem : In Fig.2 the undeformed configuration is outlined in solid lines and the deformed…

A: Consider the free body diagram ;

Q: determinant the radius of gyration

A: Radius of gyration is defined as the imaginary distance from a particular axis of its rotation about…

Q: The shape of the grain are based on the followings categories EXCEPT: (a) bulky (b) flaky (c)…

A: The shape of soil grains can be : Flaky Needle shaped Bulky

Q: Q.2) Calculate the ỹ of the centroid and Iş (with respect to centroid) for the composite area shown…

A: Considering the full rectangle: Area a1=B*D=18*74=1332 cm2 y1=D/2=74/2=37 cm

Q: Problem 1) A rectangular ASTM A36 steel bar is 2in by 6in in cross section is subjected to an axial…

A:

Q: (in %, up to two decimal places) is outer diameters of 100 mm and 106 mm. respectively. The area…

A: Find area ratio of core cutter,Ar=?

Q: What is the cracking moment of the beam having a cross section shown in Figure 1 if f ‘c = 28 MPa?.

A: Cracking Moment- Cracking Moment is the moment beyond which the concrete begins to crack.When the…

Q: Calculate quantity of the Reinforcing for the beam shown in figure below. A 0.3 m 3.2 m 2016 08 @…

A:

Q: At room temperature (20°C) a 0.5-mm gap exists between the ends of the rods shown. At what temp will…

A: The change in temperature with respect to the initial temperature of the material tends to change in…

Q: A bar of diameter 30 mm is subjected to a tensile load such that the measured extension on a gauge…

A: We have to determine the poissons ratio

Q: (in %, up to two decimal places) is, outer diameters of 100 mm and 106 mm. respectively. The area…

A: Given Outer diameter, do = 106 mm Inner diameter, di = 100 mm To Determine Area ratio of the core…

Q: The minimum thickness of a square base plate with A1= B x N=A2= 600 in2 subjected to Pu = 500 k and…

A:

Q: A bar of diameter 30 mm is subjected to a tensile Load such that the measured extension on a gauge…

A:

Q: Locate the centroid of the composite area. You can choose your own reference axes. 6cm 13cm 26 cm…

A: The centroid is defined as the average position of all points in the graph or the geometric center…

Q: s used as a tension member connected on both legs with 20 mm diameter bolts.  Given that s = 50 mm,…

A: Given:- 20 mm diameter bolts s = 50 mm t=8mm Ag=1852mm2 To find:- Design strength

Q: Determine strain in rod

A: Given data : Change in length (∆L)=5 mmInital length (L)=500 mm

Q: An aluminum [E = 8600 ksi] bar is bonded to a steel [E = 30150 ksi] bar to form a composite beam as…

A:

Q: Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area…

A: Given, A1=1.5 in2E1=2400 ksiA2=0.832 in2E2=3110 ksiL1=16 inL2=38 inQ=8.2 kipsP=3.7 kipsR=15.6 kips

Q: Question 27 An A36 angle bar is used as a tension member connected on both legs with 18 mm diameter…

A: Given:- 12 mm diameter bolts s = 65 mm, Ag = 1852 mm2  t = 8 mm To find:- The design strength (kN)…

Q: Y 3" 3"

A:

Q: If a metallic piece weighs 8 kg in air and 6 kg in water, then its specific gravity would be: a) 8…

A:

Q: 50 units 50 units A B C Which rivet is least likely to fracture first? a O A b O B C Ос d The rivets…

A:

Q: gap exists between the ends of the rods shown. At a later time when the temperature has reached…

A: We know the change in length due to temperature change is given by :ΔLT=Lα(ΔT)

Q: Three shims are being used to align a compressor and motor. The thicknesses of the shimsare 0.43…

A: Given:- The three shims are being used to align a compressor and motor The thickness of the shims…

Construction Process

In civil engineering, construction is the combination of art and science, to construct a physical and naturally built environment, starting from the design phase. The construction process falls under the area of building construction, which is a sub-branch of civil engineering. Hence, it is also sometimes called the design and build or design-build process. The work of construction is majorly carried out by civil engineers and design professionals along with a team of works consisting of contractors and subcontractors.