A tape is threaded over three pulleys as shown in the figure. Each of the pulleys requires a torque of 30 lb – in to make it rotate.  Assignment: In the preceding example, if T = 10 lbs and f = 0.20, find the force P to start the tape moving leftward.

Q: 7. In the wedge shown in the figure. Determine the largest angle that will cause the wedge to be…

A: As per given question  We have to determine the largest angle

Q: 4- Şekildeki mekanizma ile E ucundaki tahta sıkıştırılacaktır. Buna göre uygulanan düşey P kol…

A:

Q: In (Figure 1), P₁ = 12 kN and P₂ = 6 kN. Figure 2 m G B 1 m 2 m 1 m 1 of 1

A:

Q: olved force P so the box will rest in the position as shown in figure P-310. Assume the inclined pl…

A: Given Data : W=300 lb θ=600

Q: A Pratt truss supports three forces at joints along the bottom edge, as shown in the figure below.…

A: A Pratt truss supports three forces at joints along the bottom edge, as shown in the figure…

Q: Find the magnitude of the compressive force acting on the gate shown in the figure and then…

A: Given:

Q: Problem 1 Determine the reaction at A and C. Support at A is fixed, C is roller support, and B is…

A:

Q: Since the force on the wheel is F = 3.4 kN, as in the figure, calculate the joint force FA and the…

A: Given Data

Q: The rigid arm of negligible weight shown in the figure supports a load of F = 852 N. The chains are…

A: Given data: F=852 Nx1=5 mx2=4 my=7 mz=5 m Need to determine the Magnitude of the force in FBE.

Q: Determine the force Vectors F = 90 N and F43 in the four bar mechanism shown in figure below. Draw…

A: Given: F = 90 N OQ = 80 cm OA = 50 cm AB = 70 cm QB = 60 cm QE = 34 cm For this mechanism to be…

Q: The mechanism in the figure below is designed to maintain the horizontal position of the load while…

A: Given values  a=34cm, b=68cm, c=20cm, r=93cm, m=110kg Given figure

Q: The system shown in the figure is subjected to a force of F = 509 N 1) Calculate the magnitude of…

A: Given data as per the question Force =509 N

Q: The system in the figure is in equilibrium. A concrete block of mass 265 kg hangs from the end of…

A: Given-To Find-(i) Tension  in the cable(ii) horizontal component of Force on strut from hing(Iii)…

Q: 1000 lb 4 ft 4 ft B 5 ft A 3 ftr 10 ft 13 ft 600 lb -9 ft- 5 ft E Show Transcribed Text The frame is…

A:

Q: Find the slack-side tension on pulley A in N.

A: Solving Part A , we assume that torque is transmitted undiminshed

Q: ) The Figure shows a crank loaded by a force F1= 1300 N and F2 = 300 N that cause tensions in a 19mm…

A: Given data :- Force F1= 1300 N and F2 = 300 NTo determine :- a) Draw the free-body diagrams of…

Q: The figure 2 shows a four-bar linkage with an external force applied at point B. Draw a free-body…

A:

Q: Q(1): If the force system shown in figure (1) is in a balanced system, calculate the force and the…

A: Since you have asked multiple questions in a single request, we would be answering only the first…

Q: A shaft in equilibrium is shown below with dimensions as given in the table below: a b da dB dshaft…

A: Given data:

Q: For two existing torques, what third force at a given distance from the pivot will balance them?…

A:

Q: An inclined truss supports three forces at joints along the left edge, as shown in the figure below.…

A:

Q: The slender plank shown in figure is held in equilibrium by the action of the force Fp. Find the…

A: Given, m = 200 kg

Q: 8. Refer to figure 9. Given the following information: angles 0r= 20°, 02= 30°, 03= 41°, a 200 N…

A:

Q: 75 lh 10 in. -10 in. for pin A and roller B for five different values of a Calculate reaction forces…

A:

Q: The specialty wrench shown in the figure is designed for access to the hold-down bolt on certain…

A: The given force in vector is The position vector of the force can be determined as shown below.

Q: В G 5 m

A: For solution refer below images.

Q: In the design in the figure, a force of Fn=1912 N in the vertical plane and a torque of Md=916 Ncm…

A:

Q: A plank 25 meters long is placed on rough inclined planes at an angle of 15 with the horizontal as…

A: For Find the value of x, 1). first apply force equilibrium eqn. along the plank and find relation…

Q: The 6.0-1b bar is pinned at its center O and connected to a torsional spring. The spring has a…

A: In this problem first the moment about O is taken and the acceleration is integrated to get the…

Q: An axle is composed of elements laid by S355 E-module 2.1x105 N/mm2, transverse contraction factor…

A: it appears to be a schematic of a shaft under bending load. Here's how to approach the problem:v)…

Q: Calculate the forces arising on A, B and D pins with the effect of 500N horizontal force in the…

A:

Q: 3 digits behind comma From the given figure, F = 100 N. • Draw the FBD 1000 mm • Draw the action…

A: given data: F=100N AB=125mm BC=1000mm force at B?? force at A?? RAV=vertical force at point…

Q: A countershaft carrying two V-belt pulley is shown in Figure 1. Pulley A receives power from a motor…

A: Given: The tension on the loose side of belt, T2 = 0.15T1

Q: A single-piece bicycle crank is shown below under the following load: the rider pedals forward with…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.