A tank in the shape of the frustum of a cone has a bottom radius of 0.75 m, top radius of 1.5 m and 2 m high. Find the work required in kN-m to pump the full content of the tank (water) to a point 1 m above the top

A tank in the shape of the frustum of a cone has a bottom radius of 0.75 m, top radius of 1.5 m and 2 m high. Find the work required in kN-m to pump the full content of the tank (water) to a point 1 m above the top

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

complete solution thankyou
1.) A tank 1.20 m wide and 2.0 m long, supported on frictionless rollers, contains water having a depth of 1.8 m. In one end of this thank, an orifice having an area of .015 m? and a coefficient of discharge of 0.60. If the center of the orifice is 1.20 m below the water surface, what force will be required to keep this tank stationary?
The reservoir's water flow traverses a 15-meter-long spillway, lowering the water's height from 83 meters to 81.5 meters, with the crest elevation at 80 meters, in 30 minutes. Apply C = 1.84. A) What is the reservoir's area?B) How long does it take to extract water from an elevation of 83 m/80.2 m? C) After 20 minutes, what is the water's ultimate elevation?
4. A horizontal boiler drum 6m long and 3m diameter is provided with an orifice 100mm in diameter at its bottom. It contains water up to a height of 2.4m. Calculate the time taken to empty the drum.
A vertical circular tank that is 1,5 m high, has sloping sides. The tank is 50 m and 30 m in the top and bottom diameters respectively. Discharge takes place through a triangular orifice situated at the bottom of the tank. The orifice has a base of 0,8 m long, 0,5 m below it's vertex. If the tank is originally full of water, what time is required to empty the tank? Take discharge coefficient as 0,63.
A vertical circular tank that is 1.5 m high, has sloping sides. The tank is 50 m and 30 m in the top and bottom diameters respectively. Discharge takes place through a triangular orifice situated at the bottom of the tank. The orifice has a base of 0.8 m long, 0.5 m below its vertex. If the tank is originally full of water, what time is required to empty the tank? Take discharge coefficient as 0.63 Show all formulas and values that are substituted PLEASE
Water is flowing in a 3 m wide rectangular channel. A hydraulic jump occurs and the flow upstream is 360 mm deep while the flow downstream from the jump is 1300 mm deep. A) Find the discharge flowing in the channel. B) Find the energy absorbed by the jump in kW. Please answer correctly
A storage reservoir supplies water to a pressure turbine under a head of 20 m. When the turbine draws 0.5 m^3/s of water, the head loss in the 300 mm-diameter supply line amounts to 2.5 m. -Determine the pressure intensity at the entrance of the turbine -If a negative pressure of 30 kPa exists at the 600mm-diameter section of the draft tube 1.5m below the supply line (point 3), estimate the energy absorbed by the turbine in kilowatts neglecting all frictional losses between the entrance and exit of the turbine. -Assuming a turbine efficiency of 85%, find the power output of the turbine.
A pontoon 6m x 6m x 3m floats in water with a draft of 2m. The orifice at the bottom of the pontoon is 160mm in diameter with a coefficient of discharge of C= 0.60. Determine the time required for the pontoon to sink its top after opening the orifice at the bottom.
SITUATION 4: Water is drained from a large reservoir using two horizontal pipes connected in series. The first pipe is 20 m long and has a 10-cm diameter, while the second pipe is 35 m long and has a 4- cm diameter. The water level in the reservoir is 18 m above the center line of the pipe. The pipe entrance is a sharp edged, and the contraction between the two pipes is sudden. Neglecting the effect of the kinetic energy correction factor, determine the discharge rate of water from the reservoir. Assume the friction factor for all pipes is equal to 0.02 and the loss coefficient is 0.05 for a sharp edged entrance, and is 0.46 for sudden contraction. 18 m Oil tank 20 m 35 m
Water is flowing in AF pipe (Figure 1) at a velocity of 2 m/s and a pressure of 102400 Pa, the pipe length is 100 m. If the water pressure needs to be at a pressure of 1.6 atm on a lower level. What should be the different in elevation between the upper and lower levels in order to achieve this pressure? Take the density of water 1000 kg/m3 and gravity is 9.81 m/s2, consider the energy loss.
answer fast