A tank contains two liquids, half of which has a specific gravity of 1 and the other half has specific gravity of 2. A metal sphere with radius of 300 mm and specific gravity of 4 is submerged such that half of the sphere is in the liquid of specific gravity of 1 and the other half is in liquid specific gravity of 2. a. Determine the buoyant force acting on the sphere in N. b. Determine the tension of the cable to keep the sphere in this condition in N. c. If the liquid is all water, determine the buoyant force on the sphere in N.

A tank contains two liquids, half of which has a specific gravity of 1 and the other half has specific gravity of 2. A metal sphere with radius of 300 mm and specific gravity of 4 is submerged such that half of the sphere is in the liquid of specific gravity of 1 and the other half is in liquid specific gravity of 2. a. Determine the buoyant force acting on the sphere in N. b. Determine the tension of the cable to keep the sphere in this condition in N. c. If the liquid is all water, determine the buoyant force on the sphere in N.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

STATICS OF RIGID BODIES Three wheel loads rail as a unit across a 12m span. The loads are A-10kn, B-20kN to the right of A; and C-40kN to the right of B. Determine the magnitude of the resultant and show the distance from point A.
Consider a column bean under compression. A load P is applied at the upper end.Both ends have pinned boundary conditions. As you answer the following questions, you must explain each step, so you can show that you understand each step. You must also be concise and very brief.a.What is the critical load for this system. b.Assume that you now add a pinned supportis located a third of the way from the top of the column,and athird from the bottom of the column. These pinned supports prevent the column from laterally translating at the points of support. What is the new critical load of this system? Solve this problem in two very simple ways
B 4m 2m Hinge Water 50cm 420cm 30cm A closed cylindrical drum is 30cm in diameter and 50cm high as shown, contains a liquid (SG liquid = 0.83) and a depth of 20cm. The drum is then submerged in water and attached to a beam using a tension wire. Neglect the outer and inner thickness of the drum. To keep the beam in horizontal position, determine the following: a) The force "B" If the specific grawlty of the drum is 1.65; force "B" is Blank 1 KN b) The specific gravity of the d'um if the force B is 160 kg: SG of drun is Blank 2 Blank 1 Add your answer Blank 2 Add your answer
0131% D 14:19 8.8 TNT Wi-Fi voWiFi •4* K/s a. Which of the following is the most stressed leg(s)? b. If the capacity of each leg is 25 kn, what is the safe value of W? c. Determine the axial force on leg AD if the maximum safe value of W is applied. SITUATION 4. Knowing that do = 3m, determine the following: 2m, 3m 3m de id 4m B DI 5kN 5kN 10KN a. Distance dɛ b. Reaction at E c. Total length of cable.
Problem 6 Two cables of the same gauge are attached to a transmission tower at B. Because the tower is slender, the horizontal component of the resultant of the forces exerted by the cables at B is to be zero. Knowing that the mass per unit length of the cables is 0.4 kg/m, determine (a) the required sag h, (b) the maximum tension in each cable. -90 m- A h B 60 m → 3 m Figure Problem 6 с
Please show the FREE BODY DIAGRAM and COMPLETE CLEAR solution
None
Determine the moment of inertia of the cross-sectional area of the reinforced channel about the x-axis. Assume t = 1.0 in., a = 1.8 in., b = 1.6 in., c = 2.2 in. 一一叫 F₁-a- Answer: lx = i in.4 x
RAH RBH C SF TRBV 500 600 200 E RAH RAV RDH 120 RDV 2. Each member of the frame shown in the figure weighs 50 KN/m. Compute the horizontal and vertical components of the pin pressure at C, D and F. blem n ma In the ction
If the mass of cylinder is 100 kg, find the tension developed in wires AB and AC and find the support reactions in point O.. X 3 m 1.5 m 1.5 m 3 m. B 1 m