A T beam for a floor system has a slab thickness of 100mm and total depth of 550mm. bw=300mm. The beam has a span of 6m with a spacing of 2.4m center to center. The beam carries a live load moment of 184 kN.m and dead load moment of 84 kN.m f'c = 20.7 Mpa, fy= 413.7. Steek cover = 65mm A.Determine the effective flange width (m) B.Determine the depth of concrete compression block (mm) C.Determine requires steel area,(mm^2)

A T beam for a floor system has a slab thickness of 100mm and total depth of 550mm. bw=300mm. The beam has a span of 6m with a spacing of 2.4m center to center. The beam carries a live load moment of 184 kN.m and dead load moment of 84 kN.m f'c = 20.7 Mpa, fy= 413.7. Steek cover = 65mm A.Determine the effective flange width (m) B.Determine the depth of concrete compression block (mm) C.Determine requires steel area,(mm^2)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a) The floor system shown is subjected to a total uniform distributed load of 12 KN/m². Sketch the loading that acts along the members DE and BDG. -2.0 m - 3.0 m- A 3.0 m D E 5.0 m F G
"D.60. Compute the ultimate strength capacity of the positive moment beam design below. f'c= 28 MPa, fy= 414.6 MPa, bf= 760 mm, t= 85 mm, hw= 440 mm, bw = 420 mm ds= 10 mm, ct= 30 mm, cb = 35 mm. Steel bar details: compression side at top (single layer): 3 - 16 mm dia. , tension side (double- layered): upper layer is 4 - 28 mm dia. and lower layer is 4 - 28 mm dia." Use the editor to format your answer br Ct t Bar diameters and positioning in the figure given are just representations. Refer to the problem ds hw statement for the number of bars and bar diameters to use in your computation. 25 mm Cb bw
3
Situation. A flooring system consists of parallel I-beam sections spaced at 3 m. on centers simply supported over a span of 9 m. The beam supports a 200 mm thick concrete slab of ultimate strength f'c = 21 MPa. The flooring system is designed for as ceiling and floor load of 750 N/m². The properties of the I-beam sections are: A = 11,500 mm² d = 350 mm; tw = 10 mm bf = 250 mm; t = 16 mm lx = 266x106 mm4 ly = 45 x 106 mm4 fy = 248 MPal Wb = 90 kg/m fy = 248MPa If each beam is laterally braced by the concrete slab, calculate the allowable bending strength using safety factor of 1.67. Select the correct response: 175.17 248.79 235.94 394.03
HW A shaft composed of Segments Ac, CD and DB fastened to rigid supports and loaded as shown, for st G=83 GN/m², for Aluminum G =28GN/m² and for br G= 35 GN/m² Determine the maximum shearing Stress developed in each Segment? Steel d=25mm 2m Ans: TB-472 N.M, TAI = 9.1 TD=700N.. Tc=300N.m Aluminum d= Semm 1.5m & ₁ B Bronze d=25mm Im
1. A rectangular beam has b = 300mm, d = 500mm, As = 6 – 32mm diameter bars, fc' = 27.6 MPa, fy = 414 MPa. Calculate: a) depth of compression block, "a" b) fs c) + d) Mu
Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 13 MPa. Answer must be in mm. Given: a = 1 m, b=4 m, c = 2 m, P=6 kN, and w 3 kN/m.
"D.35. Compute the ultimate strength capacity of the positive moment beam design below. f'c= 25.8 MPa, fy= 506.8 MPa, bf= 710 mm, t= 90 mm, hw= 470 mm, bw = 440 mm ds= 10 mm, ct- 30 mm, cb = 35 mm. Steel bar details: compression side at top (single layer): 4- 16 mm dia. , tension side (double- layered): upper layer is 4 - 28 mm dia. and lower layer is 5 - 28 mm dia." Use the editor to format your answer br ... Ct Bar diameters and positioning in the figure given are just representations. Refer to the problem statement for the ds hw number of bars and bar diameters to use in your computation. 25 mm Cb bw
RUSH
5 m T Į 2.5 m 10 kN B A с D 10 m For the portal frame shown in the above figure, the final end moments are: 'AB' - 15 kN.m, MBA=10 kN.m, McD = 20 kN.m, The end moment at Moc will be CD DC
Question 4) Check the maximum permissible A, to ensure ductile behavior. Compute the design moment strength øMn. Use fy = 60000 psi and f = 4000 psi. %3D -6 in.- 3 in. 2 #9 6 in. 12 in, 30 in. 6 in. 5 #11 3 in. 3 in. +4 @ 3 in. = 12 in. +3 in. 18 in.-