A survey line AB crosses a river. A line AP is run perpendicular to the survey line having length 200m. Another line PB is set at right angle to QP such that tho point tho curvoy lino at

Q: HO SE 25 um DETERMINCE tHE DIA Fcow RATE Q WHUN helm

A: Given:- Diameter (D) = 2.5 cm = 0.025 m Height (h) = 1 m  To Find :- Flow rate (Q)

Q: 15 15 45 .75

A: Orthographic projection of given isometric drawing is shown below

Q: 470 53 las a. Resultant created by two Fone direction prom the pore es ņ Angle po sitive hori 2on…

A: to determine- a) resultant force b) direction of the resultant force from the positive x axis

Q: Figure 1. Length of line AC? a. 8.33" b. 5.83" c. 9.72" d. 11.33"

A:

Q: Calculate the Maximum Y distance on the drawing below: 1.000 O .510 O .500 O 2.009 C .460 2.000…

A: Maximum  Y distance is possible when the right side hole is having minimum diameter. The distance…

Q: What is Line B?

A: Solution:

Q: Q3) Determine the x- and y-coordinates for the shaded area as shown in figure (3), noted that all…

A:

Q: what is the length of the red line?   it cannot be 0.5 becasue those lengths are not on the same…

A: Given Figure to find the length of the red line?

Q: Q3) Determine the x- and y-coordinates for the shaded area as shown in figure (3), noted that all…

A:

Q: 15 D 4 holes 15 Deep 75R 20 50D 35 Deep BRACKET Draw the three Principal Views and Section. Include…

A: Draw three principal views and include all the dimensions.

Q: to goxo Yo²o, and p¹ = [1]. Find rotation matrices R and R, and show that RR = 1, where I is an…

A: The preceding method entails applying linear algebra techniques to the issue of determining the…

Q: 3. A line AB 60mm long is situated in H.P and inclined to V.P at 30 deg. The end A is 20mm in front…

A: Given Length of line AB = 60 mm Angle of inclination with vertical plane = 30o Point A is above the…

Q: *find the area bounded Curve y=K+5. line Xz

A: First find the intersection point: y=x2+5x=y66x=x2+5x2-6x+5=0(x-1)(x-5)=0x=1, x=5y=6, y=30

Q: 1.o. --O f₁ 0 f₁ x- 2" 0- fz

A: The sketch is shown below, as per the principles of ray diagram.

Q: The engine room of a freighter is on fre A frefghting tugboat has drawn along sde and is drecting a…

A:

Q: Draw the section view (locate the section line/cutting line along midpoint of dim 71 )

A:

Q: The new coordinates of translated the triangle ABC, A(2,2), B(3,2) and C(2,4) by 2 units in…

A: Given:A(2,2)B(3,2)C(2,4)tx=2ty=3

Q: i need the isometric of this projection

A: Refer the below image for the required isometric view for the given orthographic views.

Q: Evaluate the integral dy dx using polar coordinate

A:

Q: e airplane is degrees

A: 5.99deg

Q: Determine V = V₁ - V2 and the angle 0 which is the angle that defines vector V and positive x-axis.…

A:

Q: Draw the section view (locate the section line/cutting line along midpoint of dim 71 ) with…

A: The sectional view is drawn by constructing the solid model and sectioning it. The various…

Q: A reverse curve connects three tangent lines with azimuths AB=252°16’ ; BC=314°10’ and CD=216°48’,…

A: from figθ+I1=90+ϕI1=90+44°10 '0'-72°16'0''I1=61°54'0''     1st curve intersection…

Q: Draw projections of this plane and find its inclination with the HP

A:

Q: Q/DRAW THE PROJECTIONS OF A SHAPE

A: According to the details provided in the question, we need to calculate projections of the object.

Q: Calculate the Maximum X distance on the drawing below: 1.000 C 2.000 Ø.995-1.000 6.00 0.008MABC X…

A: Maximum distance of X on the drawing is to be calculated.... Remember that maximum distance of X is…

Q: Prove that sin 20 + Try cos 20 and cos 20 - Ty sin 20 2 2

A: Stress Transformation  The normal and shear stresses perpendicular and parallel to the joint must be…

Q: Assignment 3.: A line AB, 55mm long, is parallel to HP and VP. It is 20 mm in front of VP and 30 mm…

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.