A stream function is given by Y= 3 x^2-y^3. Determine the magnitude of velocity in m/s at point (2,1). 12.37 1000 153.1 15.31 None of the above

Q: why is NB=0

A:

Q: dy = m y2 dx

A:

Q: Answer by true or false for the following       Specific heat is a measurement of the ability of the…

A: The specific heat of a substance is defined as the amount of heat to increase the temperature of the…

Q: re 2) mine the smallest allowable diameter of the roc able bending stress is allow = 225 MPa.

A: Apply the moment equilibrium condition about point A.The force equilibrium condition along the…

Q: Double acting cylinder cannot be used as a single acting cylinder. Select one: O True O False

A: Single Acting cylinder as it were expands by weight from a pump and after that withdraws by the…

Q: nd Steel, respectively. Given the modulus of elasticity of materials are Ealuminium = 69 G %3D…

A:

Q: If A=0.375 inch, B=0.923 inch, C=1.0992 inches, find G A 기사 W -|×|-> G- -B- -C- F E-

A: If A= 0.375 inch, B=0.923 inch, C=1.0992 inches,find G.

Q: The figure shows a cylindrical shell very long, of length L, very internal radius large r1, outer…

A: The figure shows a cylindrical shell very long, of length L, very internal radius large r1, outer…

Q: find closure Eq.

A: You have mentoned the postions and angles .

Q: Sorry that's the wrong answer it is 0.62

A: Power coefficient = Cp=0.24 Wind speed = Vw=10.3 m/s Blade length = R = 34 m The power generated by…

Q: A pneumatic system operating at 85 psi comprises a series of pneumatic actuators which consume 2.4…

A: Original CFM = 2.4 CFMOriginal pressure= 85 psiNew pressure= 120 psiAtmospheric pressure= 14.7 psi

Q: 400 300 stn 60

A: 400sinθ=500sin60=5003/2=10001.732=578.03

Q: The pipe assembly shown is subjected to a force F= 600 N. The pipe has an inner diameter of 20 mm…

A: Consider the Free Body Diagram: Torque,T=600*0.2 =120 N.mTorque acting on part BC,TBC=120 N.mTorque…

Q: The first moment of an area (mm3) about the x-axis (Qx) is O 462,000 O 594,000 O 246,000 864,000

A:

Q: QUESTION 3 Which of the following gives the nearest value for the velocity (in m/s) when the block…

A:

Q: y F1 = 30 N 3 4 F3 = 50 N 20° F2 = 20 N

A: From the data given in question, F1 = 30 N F2 = 20 N F3 = 50 N

Q: R L2 (Side view) (End view)

A: Given data: α (Bend angle) =70° Kba (Strecth factor) =0.33  t  (Stock thickness) = 0.3" R (Width…

Q: P? P G P

A:

Q: tan30*sin30

A: Given, Value of tan30 and sin30 is, tan30°=0.577sin30°=0.5

Q: Calculate the linear speed of the needle at the instant that theta equals 30 degrees and the wheel…

A: To find - The linear speed of the needle at the instant that theta equals 30 degrees and the wheel…

Q: Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive…

A:

Q: how did you find d1 and d2

A: This question is based on the concept of polar radius.

Q: Q.1) Knowing that the tension in cable BA is 570 N, determine the moment about O. Neglect the…

A:

Q: Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium, Brass and Steel,…

A:

Q: The L2 steel bolt as shown in Figure 4 has a diameter of 5 mm, and the link AB which is made from…

A:

Q: R M P

A: given; lets take tension force in member NJ=T1lets take tension force in member NM=T2lets take angle…

Q: FA -X B FB Alpha = 34 degrees

A:

Q: F E F to

A: for solution refer below images.

Q: 100 mm 100 mm 10 mm 10 mm. 200 mm 100 mm f 10 mm I II

A: For the selection of sections, we have to calculate the maximum bending stress in the beam. From the…

Q: Determine the x, y, z components of reaction at the thrust bearing D 0 = 0°.

A:

Q: Represent the following as a number between 0.1 and 1000 using an appropriate prefix:568(10^5)mm

A: Given: The given number is N=568×105 mm. The conversion factor to convert the given unit in the…

Q: What is the meaning of + S.F, -S.F, +B.M and ?- B.M

A: There are sign convention for shear force and bending moment.  The shear force at a cross-section is…

Q: Z is incorrect

A:

Q: What is the radius equivalent to Mohrs Circle?

A: Method to construct Mohr's circle, First Plot point A σx,-τxy, & B σy,τxy on σ - τ plane. Now…

Q: Which is figure depicts the ideal diesel cycle processes? Caipr rejeto. V3=Uz B. C S.

A: Ideal diesel cycle is combustion process in IC engine which comprises the four process to complete a…

Q: From the following identify the true statement. O In electrical safety precaution, all non-metallic…

A: out of the 4 statements

Q: Interpret the significance of the letters shown in the illustration

A: Instruction given at tail of the welding symbol is "See detail A".Here detail A will have the…

Q: From the following identify the true statement. O In general safety precaution, the operator should…

A: In general safety precaution main motto is to stay safe and stay alive.. Operator should know how to…

Q: A Before Ater False True O

A: Suppose Mass of Ball (A) = Ma                  Mass of Ball (B) = Mb  Initial velocity of mass A is…

Q: Given the force in spring AD (150N), final length of spring EC (0.8m), spring constant k = 9 N/cm,…

A: As per give condition,  For solution refer below images.

Q: An exponent, such as the 4 in the expression 94, means: the number of times the number before the…

A: It is required to determine value of 94

Q: Answers: FA= FB = i i kN kN

A:

Q: At a certain instant, the particle of mass m has the position and velocity shown in the figure, and…

A:

Fluid Kinematics

The branch of science that deals with objects which are either in motion or stationary are studied under the branch of classical mechanics. Fluid mechanics is a subcategory of classical mechanics that deals with the behavior of fluids at rest (fluid statics) or in motion (posing some velocity). In fluid kinematics, studies focus on the associated motion of fluid particles or groups of particles, and its associated parameters like displacements, velocity, and acceleration without concerning about the forces that caused the motion. All the laws of classical mechanics are applied in the study of fluid kinematics.