A storage tank measuring 1.50 m by 2.65 m on the bottom is filled at a rate of 74 L/min. Determine the time required for the fluid to reach a depth of 24 cm. Provide answer in minutes, to the nearest 100th. Your Answer:

A storage tank measuring 1.50 m by 2.65 m on the bottom is filled at a rate of 74 L/min. Determine the time required for the fluid to reach a depth of 24 cm. Provide answer in minutes, to the nearest 100th. Your Answer:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A conical tank 4.5m on top and 4,7m tall has a 60mm diameter orifice at its bottom for its outlet. Assume C = 0.63. The tank is filled with 7000 liters of water. What is the depth of the water in the tank in meters? How long will it take to drain the content of the tank in minutes? show solution and diagram
A volumetric tank 1.20 m in diameter and 1.50 m high was filled with oil in 16 minutes and 32.4 seconds. What is the average discharge? a. 100.5 L/min b. 102.5 L/min c. 103.6 L/min d. 108.7 L/min
An oil of density 850 kg/m3 is pumped in a pipe of diameter 20 cm. The discharge is measured as 0.015 m/s. The drop in pressure in a length of 800 m of pipeline, both ends of which are at the same elevation is measured as 98 kPa. Assuming Re < 2000, calculate the value of absolute viscosity of the oil.
What is the gauge reading p₂ in mm of mercury in the below figure ? The turbine develops 370 kW , when a discharge of 2 m³ / sec is flowing through it . Explain
Show complete solutions with figures
A closed tank containing 2 layers of fluids is discharging its contents through an orifice as shown in the figure. The circular orifice has a diameter of 48mm with a discharge coefficient of 0.65. Considering a pressure reading of 148kPa on the surface of the fluids within the tank, determine the discharge flowing out of the orifice (in L/s)? The gasoline layer is 4.0m deep with a specific gravity of 0.69, while the water surface is 5.5m above the orifice. Air: kPa gage V Gasoline %3D D = mm Water
There are two liquid tanks A and B connected to each other by a tube as shown in the figure.The base of A is 75 cm2 and the base of B is 30 cm2. The density of the oil is 0.8. How many kilograms of oil must be put in tank B so that the level difference between the water in the two branches is 15 cm? Which point supports more pressure, C or C'?
mater 3
help pls
In a system, an open cylindrical steel tank, which has a density of 7820 kg/m^3, has an inside diameter of 4.0 m and an internal height of 5.0 m. From being initially empty, exactly 2,582.13 slugs of water were poured into the tank. Next, another liquid mass, equivalent to 1,626.742 slugs, was poured inside the tank. After settling, this fluid occupied three-tenths of the total internal height of the container. Then, mercury was poured into the tank. After the fluid has settled, the height of the mercury layer was measured to be one-fifth of a meter. Finally, oil, with S.G.=0.80, was poured to fill the remaining empty volume of the tank. 1) Draw the vertical profile of the tank and label properly all the liquid layers, indicating properly the value of specific gravity used for each liquid layer. 2) What is the total mass of the system if the tank itself has a volume of 2.29 m^3? 3)Solve for the hydrostatic gage pressure at the liquid surface, at the interfaces between any two…
A cylindrical tank having a diameter of 3.5m and a height of 10m is full of water. there is an orifice at the bottom of the tank having an area of 0.025 m^2. if the tank has a coefficient of discharge of 0.60, how long will it take to empty the tank in minutes?
Oil is filled within a tall cylindrical tank. A flat disk with a height of 1 cm and with a diameter of 5 cm is placed into the oil. There occurs a narrow spacing of 0.1 mm between the disk and the tank wall. Due to the forces acting on the disk, it moves downward, and after some time, the speed of the disk reaches a terminal velocity. Beyond this moment, measurements reveal that the disk moves 30 cm in 4 seconds. If the oil density is 600 kg/m3and the specific gravity of the disk is 1.5, determine the oil’s viscosity.