A Stirling engine involves: (1) isothermal heat addition → (2) isochoric heat removal → (3) isothermal heat removal → (4) isochoric heat addition. The engine uses one mole of ideal monatomic gas and operates between a hot and a cold reservoir at temperatures TH = 400 K and Tc = 300 K, and a volume of V - 11 and Vo = 31 Calculate the heat removal/addition in part (3) of the cycle

A Stirling engine involves: (1) isothermal heat addition → (2) isochoric heat removal → (3) isothermal heat removal → (4) isochoric heat addition. The engine uses one mole of ideal monatomic gas and operates between a hot and a cold reservoir at temperatures TH = 400 K and Tc = 300 K, and a volume of V - 11 and Vo = 31 Calculate the heat removal/addition in part (3) of the cycle

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A Carnot refrigeration cycle is used as a reference to estimate the energy needed in an attempt to reduce the temperature of a laboratory sample to absolute zero. Suppose you want to remove 0.01 J of energy from the sample that is at 2x10-6K. If the high temperature is 20°C, the heat required is 982.05x10-5J. Analyzing these considerations, calculate the increase in laboratory entropy and the decrease in entropy in the sample.
i need the answer quickly
A medium size power station is used to produce 30 MW net power for a refinery. The station uses steam as the operating fluid and operates according to the Carnot cycle between the pressure limits of 0.4 bar and 35 bar. Steam enters the boiler as a saturated liquid and leaves it as a dry saturated vapour. ist t Reneric o "nd h Ts diaar ntion of s) (ii) Determine the dryness fraction of the steam that is fed to the condenser. (4 marks) (iv) Determine the specific enthalpy values at the four key points of the cycle. (6 marks) Calculat "Fic of the cycle (5 Ma, KS) (vi) Determine the thermal efficiency of the cycle. (1 mark) (vii) Using the highest and lowest temperature values in the cycle, re- calculate the efficiency of the cycle and show that it is equivalent to the result in part (vi). (2 marks) arks). 2.
16-16M Consider an air-standard Otto cycle that has a compression ratio of 8.3 and a heat addition of 1456 kJ/kg of air. If the pressure and temperature at the beginning of the compression process are 0.95 bar and 7°C, determine (a) the maximum pressure and temperature for the cycle, (b) the thermal efficiency, and (c) the mean effective pressure, on the basis of Table A-SM. 16 11 nir stand
As shown in the figure, when the temperature was 20 ° C, a 0.5 mm gap was left. Just determine the approximate value of the Temperature (° C) needed to close the gap.
Steam at 50 bar and having an enthalpy of 3100 kJ/kg is supplied to a turbine and comes out at 0.10 bar and enthalpy of 2100 kJ/kg. A feed heating is done by extracting the steam at 3.2 bar with an enthalpy of 2500 kJ/kg. The condensate from condenser with an enthalpy of 125 kJ/kg is fed into the feed heater of direct mixing type. The quantity of bled steam is 11200 kg/hr. Find the power developed by the turbine. Neglect pump work.
In the condenser of the power plant, Ammonia is isobarically condensed to saturated liquid state with 615.2kPa and x = 0.9, the mass flow rate is 4 t/h. The heat rejected from the condensing ammonia is added to heat water, which is heated from 277K to 281K. What is the mass flow rate of water in t/h. Also sketch the T-s and P-v diagrams.
A simple steam power plant uses water as the working fluid and operates on the simple ideal Rankine cycle. The boiler operates at 15000 kPa and the condenser at 30 kPa. Show the cycle on a T-s diagram with respect to saturation lines and determine the phase change in each state, the minimum temperature required at the turbine inlet such that the mixture at the exit of the turbine is not lower than 80 percent and the thermal efficiency of the cycle
In a gas turbine power plant, air at 10°C and I bar is compressed to a pressure of 4 bar by a compressor. The air is then heated in a 100% efficient heat exchanger and in the combustion chamber to a temperature of 700°C. heat exchanger and the combustion chamber is 0.14 bar. Calculate the power plant efficiency.
At P = 22 kPa, 0.9 quality steam (H = 2377 kJ/kg) enters a condenser. All of it condenses and the pressure remains 22 kPa. What is the specific enthalpy of the outlet stream?
Consider an engine operating on the following cycle using 4 moles of neon as the working fluid. Starting at a pressure of 5 atm and a volume of 2m3, the gas expands isothermally to a volume of 3m3, then is compressed isobarically back to 2m3, and finally returns isochorically to the initial state. What is the efficiency of this engine?