Problem 4A stepped steel (G=80 GPa) shaft (all solid rod) hasthe dimensions and is subjected to the torques shown35 kN-mbelow. Determine(1) The maximum shear stress(2) The rotation of a section 2m with respect to160 mm100 kN-mwall A20 kN-mB100 mm(3) The rotation of a section C (2.5m) with1 m50 mmrespect to wall A(4) The rotation of a section D (4.5m) with1.5 mC5 kN-mrespect to wall A(5) The rotation of the section at the right end Ewith respect to wall A2 mE0.5 m

torque in different portions of beam For ED torque TED=5 KN-m , dia D1=50mm and lengtht L1=0.5…

A stepped steel (G=80 GPa) shaft (all solid rod) has the dimensions and is subjected to the torques shown 35 kN-m below. Determine (1) The maximum shear stress (2) The rotation of a section 2m with respect to wall A 160 mm 100 kN-m 20 kN-m B 100 mm (3) The rotation of a section C (2.5m) with 1m 50 mm respect to wall A (4) The rotation of a section D (4.5m) with 1.5 m 5 kN-m D respect to wall A (5) The rotation of the section at the right end E with respect to wall A 2 m E 0.5 m

A stepped steel (G=80 GPa) shaft (all solid rod) has the dimensions and is subjected to the torques shown 35 kN-m below. Determine (1) The maximum shear stress (2) The rotation of a section 2m with respect to wall A 160 mm 100 kN-m 20 kN-m B 100 mm (3) The rotation of a section C (2.5m) with 1m 50 mm respect to wall A (4) The rotation of a section D (4.5m) with 1.5 m 5 kN-m D respect to wall A (5) The rotation of the section at the right end E with respect to wall A 2 m E 0.5 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A stepped shaft ACB having solid circular cross sections with two different diameters is held…

Q: tor psi ong hollow steel shaft. Note that the inner diameter of the shaft is two-thirds of ter…

A: Torque=100 kip.ftMaximum shear stress=8000 psiLength of shaft=16 ftOuter Diameter=DInner…

Q: /m

Q: A helical spring composed of 20 turns is fabricated by wrapping wire 10 mm in diameter around a…

Q: An T short column is subjected to an axial compressive force of 20 kN at P as shown in Figure Q.3a.…

Q: In order to reduce the total mass of the assembly, a new design is being considered in which the…

A: This question is related to the Torsion from strength of materials. In this question we calculate…

Q: In Fig. below, the vertical shaft and the pulleys keyed to it may be considered to be weightless.…

Q: tension load of P = 181 kN, as shown. Determine

Q: Determine the maximum absolute bending strain in the following tubular shaft if di = 160 mm and do =…

A: Determine the maximum absolute bending strain???

Q: The steel shaft shown rotates at A B C 4 Hz with 35 kW taken off at A, 20 kW removed at B, 55 mm o…

A: Answer We need to find the Torsion from the given power at A,B and C. Using the Torsion acting on…

Q: 23/Find the maximum shear stress. 4 kN/m 5 kN Im 2 kN.m 2m 2m 2m 2m 5 mm E=200 GPA 20 mm -50 mm-…

Q: 8.20 A solid shaft has diameter 80 mm. It is subjected to a torque of 4 kN-m. The maximum shear…

A: Given data: Shaft diameter, d = 80 mm Torque, T = 4 kN-m

Q: Find the max. shear stress at section а......а, T = (MPa) Ilomm 7KN 25 KN A 4. Hoomm 2m 2m 2m lomn-…

Q: Determine the maximum shear stress in the T-beam at section C. 10 kN/m 150 mm 150 mm 30 mm |C -1.5…

A: Shear Stress at point,ζ=VAyIbV=Shear for at the concerned sectionAy=Moment of area of the section…

Q: Am 60 300 mm 300 mm 300 mm

Q: Two solid steel shafts (G = 77.2 GPa) are connected to a coupling disk B and to fixed supports at A…

A: Given data : G = 77.2 GPa A) Reaction at each support B) Max. shear stress in shaft AB C) Max…

Q: Two uniform loads of 112 kN/m acting dowwnard are supported by a uniform upward pressure of q as…

A: Given:Required:Maximum shearMaximum momentLocation of zero shear from left

Q: The distributed load q and the singular moment M act on the stepped shaft given in the figure. Draw…

Q: INTERNAL DIAMETER TORQ 9 kip.ir 1.35 kl SET A 0.9 inch 12 mm 2 inches 3,000 mine the maximum…

Q: A steel penstock has a 36-in. outer diameter, a 0.5-in. wall thickness, and connects a reservoir at…

A: Given:Outer diameter= 36 inchthickness= 0.5 inchh = 600 ftRequired:Maximum normal and shear stress

Q: nine the angle of twist of poin ter of 50 mm.

A: Torsion equationfor span {0<x<0.5}T1(x)=500-500(0.5-x)=250+500xfor span…

Q: Under normal operating conditions, the electric motor exerts a torque of 2.4 kN•m on shaft AB.…

A: Determine the maximum shearing stress in (a) shaft AB, (b) shaft BC, (c) shaft CD.

Q: 2. A 200-mm-diameter pulley is prevented from rotating relative to 60-mm-diameter shaft by a…

Q: 200mm ISomm

A: Solution Given DiagramLong=3mOutside Diameter D0=200 mm=0.2mInside Diameter Di= 150 mm=…

Q: A steel tube with an outer diameter of 60 mm is used to transmit a 6 kN.m Torque. Determine the…

Q: A uniform load 119 kN/m is acting downward and supported by an upward uniform pressure of 51 kN/m as…

A: A loaded beam is given and it has been asked to determine maximum shear force in the beam. Please…

Q: What is the location of the absolute maximum shear from the left end of the beam? (in m) e. What is…

Q: 250 mm G = 80 GPA C. Two steel shafts are connected to a coupling disk B and to fixed supports at A…

A: Given

Q: Determine the maximum shearing stress of the beam

A: To find maximum shear stress

Q: Current Attempt in Progress The horizontal shaft with a diameter of d- 43 mm is supported by a…

A: d=43 mm D =63 mm τavg =69 MPa

Q: A solid steel shaft is to transmit a torque of 10 kN- m. If the shearing stress is not exceed 45…

A: Given data- A solid shaft- Torque T=10 kN-m, Shearing stress τ=45 MPa, To Find- The value of the…

Q: the maximum shear stress in the T-beam at point 150 mm 10 kN/m Determine C. 3m- C -1.5 m--1.5m- T…

A: Given Data:UVL=10kN/mSpan L=6m It is required to determine the maximum shear stress in the T-beam at…

Concept explainers

Equilibrium and Support Reactions

Civil engineers deal with structures that are composed of several members connected or with individual members such as beams and columns. To analyze such structures, the condition of statics must be applied. Under the static condition, the members are considered to be in equilibrium under the action of forces, that is, the members are assumed to be having negligible velocity.

Question

100%

Problem 4
A stepped steel (G=80 GPa) shaft (all solid rod) has
the dimensions and is subjected to the torques shown
35 kN-m
below. Determine
(1) The maximum shear stress
(2) The rotation of a section 2m with respect to
160 mm
100 kN-m
wall A
20 kN-m
B
100 mm
(3) The rotation of a section C (2.5m) with
1 m
50 mm
respect to wall A
(4) The rotation of a section D (4.5m) with
1.5 m
C
5 kN-m
respect to wall A
(5) The rotation of the section at the right end E
with respect to wall A
2 m
E
0.5 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Solution

VIEW

Step 2 angle of rotation

VIEW

Step 3 angle of rotation at C

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

569
8.47 Three forces are applied to 100 mm diameter plate that is attached to the solid 46 mm diameter shaft AB. At point H, determine (a) the principal stresses and principal planes, (b) the maximum shearing stress. 27 kN 50 mm 50 mm 27 kN 11 kN 200 mm
A torque of magnitude T = 1000 N-m is applied at D as shown. Shaft AB and CD have an elliptical cross-section. The major and minor diameters of shaft AB are 56 mm and 50 mm respectively, while the major and minor diameters of shaft CD are 42 mm and 38 mm respectively. Find the maximum shearing stress in shaft CD. Answer must be in MPa
A steel shaft must transmit 150 kW at a speed of 360 rpm. Knowing that G = 77.2 GPa, design a solid shaft so that the maximum shearing stress will not exceed 50 MPa and the angle of twist in a 2.6-m length must not exceed 3°. Consider the frequency fto be 6 Hz. The diameter of the solid shaft is 71.4542 mm.
A solid 0.78-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (3). a.)3.86 ksi b.) 3.51 ksi c.) 3.15 ksi d.) 5.38 ksi e.) 4.85 ksi
please answer in the nearest 3 decimal numbers
Problem # 1: A hollow shaft has an outside diameter 60 mm and a wall thickness of 1.25 mm. The maximum shear stress in the shaft must be limited to 150 MPa. Use G = 43 000 MPa. Determine: (a) the maximum power that can be transmitted by the shaft if the rotation speed must be limited to 20 Hz. (b) the magnitude of the angle of twist in a 700-mm length of the shaft when 30 kW is being transmitted at 8 rpm.
Two smooth cylinders are placed in the position shown. Cylinder A 1,000N and has a radius of 10cm while cylinder B has a radius of 8cm and weighs 750N. Cylinder A is connected by a 35cm string to the smooth wall C. What is the tensile stress in MPa, developed in the string if the diameter of the string is 10mm and angle beta is 25°? Bº ...
The copper pipe [G = 8,000 ksi] has an outside diameter of 3.625 in. and a wall thickness of 0.250 in. The pipe is subjected to a uniformly distributed torque of t = 95 lb-ft/ft along its entire length. Using a = 2.0 ft, b = 4.0 ft, and c = 8.5 ft, determine (a) the maximum shear stress in the pipe. (b) the rotation angle oc at the free end of the shaft. b B C Answers: ksi (a) Tmax i rad (b) Pc = i