A steel tape is 30 m. long under a standard pull of 6 kg. with a constant cross-sectional area of 0.05 cm? if the normal tension applied to make the tape equal to its nominal length when supported only at the end points that is the effect of sag will be eliminated by the elongation of the tape due to the application of this load is equal to 16 kg. Determine the unit weight of the tape. Modulus of elasticity of the tape is 2x10^6 kg/cm^2

A steel tape is 30 m. long under a standard pull of 6 kg. with a constant cross-sectional area of 0.05 cm? if the normal tension applied to make the tape equal to its nominal length when supported only at the end points that is the effect of sag will be eliminated by the elongation of the tape due to the application of this load is equal to 16 kg. Determine the unit weight of the tape. Modulus of elasticity of the tape is 2x10^6 kg/cm^2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Polycarbonate bars (1) and (2) are attached at their lower ends to a slider block at B that travels vertically inside of a fixed smooth slot. Load P is applied to the slider block. Each bar has a cross-sectional area of 85 mm2, a lenght of 1.25 m, and an elastic modulus E = 8GPa. Use dimensions of a = 1.15 m and b = 0.90 m. For an applied load of P =1700 N, determine: (a) the forces in bars (1) and (2) (b) the defection at B of the slider block
Problem 1: Three vertical posts AD, BE, and CF are held between two horizontal rigid plates. Posts AD and CF are made of steel (Es = 200 GPa) and have cross sectional areas of 1000 mm² each. Post BE is made of aluminum (Ea = 73.1 GPa) and has a cross sectional area of 1500 mm². Initially, there is a small gap of 0.1 mm between BE and the top horizontal plate. Then a vertical force of P = 410 kN is applied, which is more than sufficient to close the gap completely. D -0.5 m B E -0.5 m- 0.4 m F Determine the normal stresses in posts AD, BE, and CF (both magnitude and sign).
The cylindrical rod AB has a length L=6 ft and a 1.25-in. diameter, it is made of a mild steel that is assumed to be elastoplastic with E= 29 x 106 psi and dy= 32 ksi. A force P is applied to the bar until end A has moved down by an amount om Determine the maximum value of the force P and the permanent set of the bar after the force has been removed, knowing om - 0.250 in. The maximum value of the force P is kips. The permanent set of the bar after the force has been removed is in.
A copper rod with a diameter of 19 mm, modulus of 110 GPa, and a Poisson’s ratio of 0.35 is subjected to tension within the elastic region. Determine the force ( in N) that will produce a reduction of 0.003 mm in the diameter.
When a mass of m = 22 kg is hung from the middle of a fixed straight aluminum wire, the wire sags to make an angle of 12° with the horizontal as shown in. The elastic 12° Part A m 12° modulus for aluminum is 7.0 × 10¹0 N/m². Determine the radius of the wire. Express your answer to two significant figures and include the appropriate units.
А m 1 m 30 сm µc- 5cm rod AB is 1 m long and sits in a joint in A and is located on the pole BC in B. AB operates a linearly varying load with the largest value w = 80 N / m. The post BC weighs m = cm from C the force acts P on the post straight to the right. Decide the largest the force P that can be allowed before the pole starts move about µB = 0.4 and µC = 1. 10 kg, its height is 30 cm, and 5
The blue bar is made from steel with the following mechanical properties: Young's Modulus, E = 17x10° psi; Poisson's Ratio v = 0.31. The bar has a circular cross-section with diameter d= 0.50 in. being the length of each side. 557 lb 557 Ib 60 in. - Determine the following under the action of the axial load (assume elastic behavior): a. The bar's axial deformation, ô, in in.: b. The average axial or longitudinal strain, ELong: c. The change in the bar's diameter, in in.:
A railroad car and its cargo have a total weight of 50 kips. The car is sup 5-50 ported on eight wheels, each of which has a diameter of 25 in. If the co cient of rolling resistance is 0.015 in. between the wheels and the trach and the wheels share the load equally, determine the magnitude of the ho izontal force required to overcome the rolling resistance of the wheels.
A steel [E = 25500 ksi] pipe column (1) with a cross-sectional area of A1 = 5.60 in.2 is connected at flange 8 to an aluminum alloy [E = 17500 ksi] pipe (2) with a cross-sectional area of A2 = 4.40 in.2. The assembly is connected to rigid supports at A and C. For the loading shown, determine the normal force in the steel pipe (1). A (1) 120 in. B 30 kips 30 kips 144 in. C
A 13-mm-diameter steel (E = 193 GPa) rod (2) is connected to a 27-mm-wide by 10-mm-thick rectangular aluminum (E = 72 GPa) bar (1), as shown. Assume L1 = 0.74 m and L2 = 1.38 m. Determine the force P (in kN rounded to the nearest tenths) required to stretch the assembly 8.1 mm.
A tensile force of 100 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to2.01 m. The true axialstrain is?
5. In the CN Railwayproject,steel railroad rails of 9.5meters long are to be installed.If the modulus of elasticity of steel is207GPa, and if the lowest temperature considered is 18°C and a maximum temperature of 36°C is designed for, determine the clearance between the rails such that adjoining will just touch at maximum design temperature. Assume α for steel is 11.6 x 10-6/°C