A steel tape is 30 m long under a standard pull of 6 kg with a constant cross-sectional area of 0.05 cm^2. If the normal tension applied to make the tape equal to its nominal length when supported only at the end points, that is the effect of sag will be eliminated by the elongation of the tape due to the application of this load is equal to 14 kg, determine the total weight of the tape. Modulus of Elasticity of tape is 2x10^6 kg/cm^2.

A steel tape is 30 m long under a standard pull of 6 kg with a constant cross-sectional area of 0.05 cm^2. If the normal tension applied to make the tape equal to its nominal length when supported only at the end points, that is the effect of sag will be eliminated by the elongation of the tape due to the application of this load is equal to 14 kg, determine the total weight of the tape. Modulus of Elasticity of tape is 2x10^6 kg/cm^2.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

A round bar made of same material consists of 3 parts each of 100 mm, length having diameters of 40 mm, 50 mm and 60 mm respectively. If the bar is subjected to an axial load of 10 kN, the total elongation of the bar would be (E is the modulus of elasticity in KN/mm². (a) 4/1 1 1 + + (b) TE 16 25 36 (c) 1 0.4 1 1 + wwwwww + TE 16 25 36 (d) 4√2/1 1 1 www + wwwwwww + TE 16 25 36 40/1 1 1 + TE 16 25 36 — ===== + — mm mm mm mm
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm A = 400mm? A- 200mm 40KN 10KN 20KN 1.5m 2.5m 2.0m Determine the change in length of steel rod having a length of 800mm and a diameter of 6.5mm. The rod is subjected to a force P equal to 110KN. Young's Modulus is 200GPA Compute normal strain of the rod
A rectangular steel block is 3.0 inches long in the x-direction, 3.0 inches long in the y-direction, and 4.5 inches long in the z-direction. The block is subjected to a tri-axial loading of three uniformly distributed forces as follows: 50 kips tension in the x-direction, 60 kips compression in the y-direction, and 54 kips tension in the z-direction. If Poisson's ratio is 0.30 and E = 29 x 106 psi, find the uniformly distributed load that must be added in the x-direction to produced no deformation in the z-direction. Your final answer should include two decimal places
2.7 A steel control rod is 5.5 ft long and must not stretch more than 0.04 in. when a 2-kip tensile load is applied to it. Knowing that E = 29 × 10 psi, determine (a) the smallest diameter rod that should be used, (b) the corresponding normal stress caused by the load.
CLO 1: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between them which is 699.93 mm long. If the weight of the beam is 375 KN, determine the stress in the aluminum bar (in MPa). Bronze Bronze Alum Alum Bronze A in mm2 850 1500 E in Gpa 70 83 103.56 O 79.45 451.30 33.47
Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal pressure, and a torque. In points A and B, the following stresses occur due to the loading: o 63.5 MPa, B=127 MPa, = 127 MPa A.B A.B a. Determine Gmin, omax, and its direction (in degrees) from x-axis at point A. b. Determine omin, omax, and its direction (in degrees) from x-axis at point B. 1 B d O A x
۳:۵۲ ص الأحد ۷ مارس Untitled A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure below. Axial loads are applied at the positions indicated. If P = 3000 N and the cross sectional area of the rod is 325 mm2, determine the stress in each section, and total deformation of the road. E for steel is 200000 MPa, E for aluminum is 70000 MPa, E for bronze is 100000 MPa 1 2 3 Steel Bronze 4P Aluminum 1 2 500 mm 750 mm 625 m
Q- A cylindrical piece of steel, with a diameter of 60mm and length 100 mm, is subjected to an axial compressive force of 40,000 kg. If bulk modulus is 1.7 x 106 kg/cm² and poisson's ratio is 0.25 than the change in volume of the cylindrical piece is
A round aluminum alloy rod has a diameter of 12.5 mm and 1 m length. Its ultimate strength is 155 MPa and its modulus of elasticity is 70 GPa. Determine the maximum permissible axial load that may be applied if the total elongation of the member is not to exceed 2 mm. Calculate the diameter change if Poisson’s ratio=0.35.
The 1154-kg uniform bar AB is suspended from two cables AC and BD each with cross-sectional area 424 mm2. Find the magnitude of P (in N) that can be safely applied to the bar if the stresses in AC and BD are limited to 148 MPa and 86 MPa, respectively. Express your answer in two decimal places.
Q1\ A copper bar consists from three sections: sections 1 is of 25 mm diameter and 60 mm long, section 2 is of 15 mm diameter and 50 mm long and section 3 is 20 mm square and 40 mm long. The bar is subjected to an axial tensile load which induces a stress of 20 MN/m' on the smallest cross section. Determine the total increase in the length of the bar when the load is applied. For copper E=100 GN/m2.
A rectangle column 500 mm x200 mm in cross-section is subjected to a compression load 1000 KN, the stress on the column is: a. 30 MPa b. 10 MPa C. 50 MPa d. 20 MPa