A steel tape is 100m long at 60°C with a pull of 10 kg. Aline was measured and found to be 510.02 m. when thetemperature was 65 C using the same pull. If thecoefficient of expansion is 0.0000065 m/ C. What is thecorrect length of the line?а.510.27 mb. 509.96 mС.510.0366 m

Given data in question Measured length Measured pull Standardized pull Length of tape Coefficient…

Answered: A steel tape is 100m long at 60°C with…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

se in measuring a dis 00 ft when the temperature of the tape is 32°E? 11.7 An aluminum wire is stretched between two rigid supports. If the tensile stress in the wire is 5000 psi at 68°F, what is it at 32°F and 90°F? Assume that the proportional limit is 35,000 psi. 11:8 A 1-m-long-copper bar is placed between two rigid, unyield- ing 11. ich stelupe
4. A steel tape is 100 m. long at 25°C with a pull of 10 kg. A line was measured and found to be 510.02 m. when the temperature was 35°C using the same pull. If the coefficient of thermal expansion is 0.0000065 /°C. what is the correct length of line?
To measure a distance, Neslyn utilized a 30m steel tape. The tape was eventually discovered to be 0.03m too short. Do you think the tape has a 4mm cross-section? 0.3627N/m weight, and At a temperature of 25°C and a pull of 55N, it was standardized. The tape was kept horizontal and sustained at midspan with a constant tension of 50N during the measurement. At the time of measurement, the temperature was 30.7°C. Determine the adjusted distance if the measured distance is 420.67m (m). 3. Decimal places round your answer.
I need the answer as soon as possible
04: Suppose that the square plate is shown in Figure (2). It has three sides kept at temperature zero while the fourth side is kept at temperature 60 c°. Determine the steady state temperature everywhere in the plate. и ди ax²+ y² = 0 B.C. u(0,y) = u(1,y) = u(x, 0) = 0, u(x, 1) = 60 uck- 00 60 0 Figure 2
Please refer to the figure below. Determine the magnitude of the resultant couple at point D in Ib-ft. 20 1ы 200 kg 250 N 20 kN m 2 FT 200 kg
A tape of 20m length is used to measure a distance 1980 m at a temperature 35 °C oumale borte under 20 N tension force, find the correct measured distance if: down: STEFTICAGES Standard temperature20 °C Coefficient of thermal expansion 11.6*10 Mass of tape is 0.04 kg/m Standard tension 60N Cross section area of tape 2mm² Modulus of elasticity of tape 2000000 kg/cm²
to measure a base line, a steel tape 30m long standardised at 15 degree Celsius with a pull of 100N was used. Find the correction per tape length, if the temperature at the time of measurement was 20 degree Celsius and the pull exerted was 160N weight of 1cm3 of steel is 0.0786N and weight of the tape=8N, E=210000kg/m2, coefficient of expansion of tape per 1 degree celsius is 0.00000071.
2. Determine the standard temperature of the steel tape and the length of the line measured, if it was found out that at 35°C the total error due to temperature occurring was 0.03m while at 45°C the total error due to temperature occurring was 0.10m. Use C= 0.0000116/1°C.
Determine the magnitude of the friction force acting on the 100kg block shown if P=100N. The coefficient of friction is 0.20. The forces applied to the block is initially at rest.
4G. 40 6:51 10 ... 94 Quizzes A transmission tower shown below is subjected to lateral loads as shown. A =3.7 kN, B =4.6 kN, C =6.4 kN Determine the magnitude of the axial force in member EG (in kN). Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution. A-KN 1.5 m K 1.8 m B-KN 1.8 m C-KN F 1.8 m 2.55 m 2.55 m II
what will be the equivalent value of P that can be applied if the maximum vertical displacement allowed is 5mm??

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

A steel tape is 100m long at 60°C with a pull of 10 kg. A line was measured and found to be 510.02 m. when the temperature was 65°C using the same pulI. If the coefficient of expansion is 0.0000065 m/°C. What is the correct length of the line? a. 510.27 m b. 509.96 m C. 510.0366 m