A steel shaft is subjected to the two loads shown. Knowing that G=80 GpA, determine the total strain energy in the shaft.

Q: 2. If the load P on the beam below causes the end C to be displaced 10mm downward, determine the…

A:

Q: A bar BD is held in a horizontal position when there is no load by the steel wire AB. When a weight…

A: The cross sectional area of wire is The modulus of elasticity is The yield strength is The…

Q: 1. Determine the resultant internal loadings acting on the cross-section at C of the simply…

A: As per expert guidelines we are supposed to answer only the first question of the given multiple…

Q: Rigid bar ABCD is supported by two bars. There is no strain in the vertical bars before load P is…

A: (a) To find: The normal strain in bar 1. Given: The dimensions are L1=1900 mm, L2=1425 mm, a=190 mm,…

Q: The 50 mm diameter rod has a stress strain diagram as shown. Knowing that the angle of twist is…

A:

Q: The steel railroad increases its length when exposed to heat from 70°F to 95°F. The coefficient of…

A: Given data  T1=70°F and T2= 95°F Thermal expansion coefficient = 11.7 ×10-6 (m/m°C) Find the strain

Q: An air-filled rubber ball has a diameter of 150 mm. If the air pressure within it is increased until…

A:

Q: 1. Find the relationships between strain components in the polar coordinate and strain components in…

A: To find the relationships between strain components in the polar coordinate and strain components in…

Q: A rigid steel bar ABC is pinned at B and supported by two rods at A and C. There is no strain in the…

A: The change in the length of rods can be determined as,

Q: Your answer is partially correct. On the free surface of an aluminum [E=10100 ksi; v = 0.35]…

A: Note: check units of stresses as I am not familiar with units

Q: The force applied at the handle of the rigid lever causes the lever rotate clockwise about the pin B…

A:

Q: Determine the shear strain Y., at corners A and B if the plastic distorts as shown by the dashed…

A:

Q: 2. The two wires are connected at A. If the force P causes point A to be displaced horizontally 2…

A:

Q: A rectangular metal slab has dimensions 4m, 2m and 1m in the xy and z directions respectively. The…

A:

Q: A square piece of material is deformed into the dashed position. -15.18 mm В 15.24 mm 15 mm 89.7° A-…

A: Shear strain and average normal strain diagonal AC.

Q: 3. A thin strip of rubber has an initial length of 25 in. If it is stretched around a pipe having an…

A:

Q: An aluminum cube of edge length 20 cm floats on mercury. How much extra depth will the cube sink…

A: Consider at a particular temperature the aluminum cube sinks a depth h and density of mercury is .…

Q: 1. The normal strains of a solid under a uniaxial stress of 60MPa are and. When the solid is subject…

A: Given:The normal strains are given below;The uniaxial stress, The hydrostatic stress,

Q: If DC has a normal strain € = 0.003, DA has a normal strain Ey = 0.004 and at D, Yry = 0.02 rad,…

A:

Q: The piece of plastic is originally rectangular. Suppose that a = 300mm and b = 420 mm 2mm 5mm-> 2mm…

A:

Q: (a) the strain in the cable at a depth of 700 ft. (b) the total elongation of the cable.

A:

Q: A) The wire AB is unstretched when Theta = 45°. If a load is applied to the bar AC, which causes…

A:

Q: 1. Determine the internal normal force, shear force, and bending moment at point C in the beam. 300…

A:

Q: The force P applied at joint D of the square frame causes the frame to sway and form the dashed…

A: Given :θ = 3.6⁰normal strain ε =? Let D¹ be the point D deflected by load Let C¹ be the point C…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.