A steel rod with a circular cross-section hangs vertically inside a building. The rod has a length of 30 m, a diameter of 6 mm, and a mass of 65.3 N. If the rod has a 900 N mass attached to its free end, determine the maximum normal stress in the rod, taking into consideration the mass of the rod itself.

A steel rod with a circular cross-section hangs vertically inside a building. The rod has a length of 30 m, a diameter of 6 mm, and a mass of 65.3 N. If the rod has a 900 N mass attached to its free end, determine the maximum normal stress in the rod, taking into consideration the mass of the rod itself.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. The A-36 steel Bar BC had a diameter of 40 mm before the two loads, P, were applied. If after loading, the new diameter of the bar is 39.995 mm, what was P? P -1 m B 0.75 m 1 m
A steel wire (E= 200 GPa) of diameter d= 1.25 mm is bent around a pulley of radius Ro= 500 mm. What is maximum stress in the wire?
The stresses shown in the figure act at a point on the surface of a structural element. Using Mohr’s circle, determine the following: 1. Calculate the absolute value of the normal stress x at the point in MPa. 2. Calculate the absolute value of the normal stress y at the point in MPa. 3. Calculate the absolute value of the shear stress xy at the point in MPa. 4. Calculate the absolute value of the minor principal stress in MPa. 5. Calculate the absolute value of the major principal stress in MPa. 6. Calculate the absolute value of the maximum shear stress in MPa. Kindly answer all with complete solution please. Needed ASAP
1. As shown in the figure, there is a gap between the aluminum bar and the rigid slab that is supported by two copper bars. At 10°C, A = 0.18 mm. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased to 95°C. For each copper bar, A= 500 mm² E = 120 GPa, and a = 16.8 μm/(m °C). For the aluminum bar, A = 400 mm², E = 70 GPa, and a = 23.1 μm/(m. °C). Copper Aluminum Copper 750 mm
7. A steel rod 3 ft long with a cross-sectional area of 0.3 in.2 is stretched between two fixed points. The tensile force in the rod is 1200 lb at 40°F. Using a = 6.5 x 10°F andE=29 x 10° psi. a) Calculate the temperature at which the stress in the rod will be 10 ksi. b) Calculate the temperature at which the stress in the rod will be zero.
3 - A strain gauge is attached to the side of a beam, as shown by the cross-section view in the figure. When the beam is subjected to a specified uniform moment, the longitudinal strain measured by the gauge is -300μ. Plot the axial stress profile over the height of the cross- section. What is the magnitude of the moment that produced this strain gauge reading? Assume E = 75 GPa. 10↑ Strain gauge dimensions in mm 30 30 beamcross-section
F. A square rod with dimensions 0.02 m x 0.02 m x 0.5 m is attached to a solid surface as shown. If the forces on the rod are too large, it will either crush or be sheared off where it is attached to the solid surface. If the rod can withstand either a maximum normal stress of 25 kPa or a maximum shear stress is 15 kPa, a)what is the largest allowable magnitude of F, (in N) if F,=0? b)what is the largest allowable magnitude of F, (in N) if F,=0? F2
A steel wire (E = 200 GPa) of diameter d = 1.0 mm is bent around a pulley of radius Ro= 400 mm (see figure below). Ro a. What is the maximum stress in the wire? b. Does the stress increase or decrease if the radius of the pulley is increased?
A pressurized cylindrical tank with flat ends is loaded by torques T and tensile forces P (see figure). P The tank has an inner radius of r = 141 mm and wall thickness t = 6.5 mm. The internal pressure p = 7.25 MPa and the torque T = 820 N m. (Assume that the structure behaves linearly elastically and that the stresses caused by two or more loads may be superimposed to obtain the resultant stresses acting at a point. Consider both in-plane and out-of-plane shear stresses unless otherwise specified.) (a) What is the maximum permissible value of the forces P if the allowable tensile stress in the wall of the cylinder is 169 MPa? (Enter the magnitude in kN.) KN (b) If forces P = 400 kN, what is the maximum acceptable internal pressure in the tank (in MPa)? MPa
3. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 13.05 ksi, or in bronze of 100 MPа. Aluminum A = 400 mm? Bronze A = 200 mm Steel A = 500 mm? 2P 4D 2.5 m 2.0 m 1.5 m
A 20 m long steel rod is at a temperature of 20°C. The rod is heated so that temperature rises by 50°C. If rod is allowed to expand by 14 mm, what will be the stress induced in rod? Take E = 200 GPa and α = 12 x 10-6/°C.
A hollow aluminum tube used in a roof structure has an outside diameter d2= 112mm and an inside diameter d1= 80mm. The tube is 2.80m long, and the aluminum has a shear modulus of G= 28GPa.a. If the tube is twisted in pure torsion by torques acting at the ends, what is the angle of twist, in degrees,when the maximum shear stress is 52MPa?b. What diameter d, in mm, is required for a solid shaft, as shown, to resists the same torque with the same maximum stress?c. What is the ratio of the weight of the hollow tube to the weight of the solid shaft?