A steel rod having a cross-sectional area of 332 mm^2 and a length of 176 m is suspended vertically from one end. The unit mass of steel is 7950 kg/m3 and E = 200 x (10^3) MN/m2. Find the maximum tensile loạd in kN that the rod can support at the lower end if the total elongation should not exceed 65 mm.

A steel rod having a cross-sectional area of 332 mm^2 and a length of 176 m is suspended vertically from one end. The unit mass of steel is 7950 kg/m3 and E = 200 x (10^3) MN/m2. Find the maximum tensile loạd in kN that the rod can support at the lower end if the total elongation should not exceed 65 mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

roblem 2: A steel hoop, 10 mm thick and 80 mm wide, with inside diameter 1500.0 mm, is heated and shrunk onto a steel cylinder 1500.5 mm in diameter. What is the nor- mal force in the hoop after it has cooled? Neglect the deformation of the cylinder, and use E == 200 GPa for steel. roblem 3: The timber member has a cross-sectional area of 1750 mm² and its modulus of elasticity is 12 GPa. Compute the change in the total length of the member after the loads shown are applied. 40 kN 35 kN 20 kN D• A
A thin walled member of 1000 mm long has the cross-section shown in figure. Determine the maximum torque which can be carried by a section if the angle of twist is limited to 10%. What will be the maximum shear stress when this maximum torque is applied? Take G = 80 GPa. 18 mm- 2 mm 40 mm-
None
A steel rod having a length of 50m is suspended vertically from one end. It supports a tensile load of P = 250 kN at the lower end. The unit weight of the steel is 7850 kg/m^3. The allowable tensile stress for steel is 140 MPa. Use E = 200 GPa. Determine the total deformation of the steel rod.
thanks
Bar A has diameter 'd' and bar B has diameter '2d'. Both are of the same length and are of the same material. If they are subjected to same axial load P, the ratio of extension of bar A to B is (B) 2 (A) 4 (C) 0.5 (D) 0.25
At a temperature of 34°F, a 0.06 in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [a = 12.5 x 10-6/°F] and bar (2) is stainless steel [a = 7.3 x 10-6/°F]. The supports at A and C are rigid. Determine the lowest temperature at which the two bars contact each other. (1) 33m B (2) Answer: Final temperature = 55 in. -0.06. gap °F.
A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi; a = 2.9 × 10-6/°F] bar (1) and an aluminum alloy [E = 10,000 ksi; a = 12.5 × 10-6/°F] bar (2), as shown. Each bar has a cross-sectional area of 2.00 in.². The bars are unstressed when the structure is assembled at 30°F. After a concentrated load of P = 69 kips is applied and the temperature is increased to 100°F, determine the normal force in bar (1). 6 ft 2.5 ft 07.01 kips 5.63 kips 8.39 kips 9.29 kips 6.66 kips (1) B 3 ft C 8 ft 1.5 ft
A cantilever beam of length 6 m has an additional support at a distance of 2 m from its free end as shown in Figure 4. It has the cross-sectional dimensions with height h=300 mm, inside height h₁ =250 mm, width b= 150 mm, and inside width b₁=100 mm. It is made of an elastic perfectly plastic material having tensile and compressive yield stress of oy = 250 MPa. Determine the yield moment My of the beam Determine the plastic moment Mp of the beam ✓ By using force method and selecting the vertical reaction at C to be redundant, draw shear and bending diagrams using the graphical method. -Determine the minimum value of W at which collapse occurs B/2W C 77 2m 2m 2m C b₁