A steel plate is 360 mm wide and 20 mm thick with four (4) bolt holes 25mm o cut into the plate as shown. Considering all possible failure paths,which one will give the most critical net area, An? *45 mm45 mmlag60 mmb.06" 06" 06°360 mm

B=360mm t=20mm do=25mm n=number of bolt through the path considered

Answered: A steel plate is 360 mm wide and 20 mm…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

b) caliper. What is the significance of this type of measuring tool? With a well labeled diagram explain the operating techniques of micrometer screw gauge and venier 3. а) I) II) II) IV) Classify the following types of steel codes 1021 9211 7221 23XX V) 5221
Determine the design strength of an UNP300 with four lines if 20 mm diameter bolts in standard holes, as shown in the Figure below. 1= 20 mm 60 60 60 60 60 60, 60, 60, 60,60 UNP 300 F, = 370MPA F = 240MPa o o оо o o o o
Determine the tensile capacity of a 200 x 100 x 12 mm angle in S275 steel assuming that the angle is connected through the longer leg by one row of M24 bolts (Fig. 3). (3 bolts in a row and p = 70 mm) M24 P Angle 200 x 100 x 12 Fig. 3 (all units in mm) * 70 O + Ö 70 *
The minimum thickness of a square base plate with A1= B x N=A2= 600 in2 subjected to Pu = 500 k and m = 5.5 in, n= 4.1 in, and n’ = 2.6 in, and Fy = 36 ksi is equal to: Group of answer choices 7/8 inch 1 3/8 inch 1 1/4 inch 1 inch
A flanged bolt coupling is used to connect a solid shaft 110 mm in diameter to a hollow shaft 100 mm in outside diameter and 80 mm in inside diameter. If the allowable shearing stress in the shafts and in the bolts is 58 MPa, how many 16 mm-diameter steel bolts must be used on a 300 mm-diameter bolt circle so that the coupling will be as strong as the weaker shaft? This is an exception to our two decimal rule -- so our answer here must be rounded to the NEXT whole number. Previous Next ENG US
.
An A36 angle bar is used as a tension member connected on both legs with 20 mm diameter bolts. Given that s = 50 mm, calculate the design strength (kN) by LRFD with the limiting state of tensile fracture at the smallest possible net area. Write your answer to the nearest whole number.
Topic:Bolted Steel Connection - Civil Engineering *Use latest NSCP/NSCP 2015 formula to solve this problem What is the value of S if the joint is 80% efficient? Tension of Plates = 76 MPa Hole diameter (effective) = 23 mm
An A36 angle bar is used as a tension member connected on both legs with 22 mm diameter bolts. Given that s = 50 mm, calculate the design strength (kN) by LRFD with the limiting state of tensile fracture at the smallest possible net area. Write your answer to the nearest whole number. Ag = 1,852 mm2 t = 8 mm
An A36 tension member shown in the figure is connected with three 19 mm diamter bolts. Diameter of hole = 22mm. Properties of 150 mm x 100 mm x 12.5 mm angle A = 3065 mm2 y = 50.55 mm Fy = 248 MPa Fu = 400 MPa Determine the desire strength due to fracture in the net section. Use U = 0.85 kN
What is the maximum concentrated load that can be applied at the end of an embedded hollow pipe, made of AISI 1020 steel? Take 10.16 cm for the outside diameter, and 6.35 cm for the inside diameter. The length of the pipe is 183 cm. Its maximum deflection must not exceed 5.08 cm. Neglect the weight of the pipe. Answer 22816 N
Calculate the ultimate moment of the given triangular column cross-section section Mr? Paste your PEG or PNG Proof paper using menu above Na=150 kN 90 mm A = 3024 A2 =024 As2 600mm fot = 17 MPa fya = 365 MPa As1 1 60 mm 600 тm

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

A steel plate is 360 mm wide and 20 mm thick with four (4) bolt holes 25 mm o cut into the plate as shown. Considering all possible failure paths, which one will give the most critical net area, An? * 45 mm 45 mm la e g 60 mm 360 mm 06" 06" 06