A steel pipe is supported as indicated in the figure and loaded by a force P at x =Assume L = 10m, Pipe outer diameter (OD): 5", Pipe inner diameter (ID): 4.209", k=1.0 x 10³N/m, Steel: E-2.1 x 10¹1 N/m², P= 5000 N.Calculate the reaction forces at S and B.Show all work and FBD's as partial credit will be given.kwww.XP

Given data : P = 5000N , L = 10m , X = 8m , k(spring constant) = 1×108N/m , E = 2.1×1011 N/m2…

A steel pipe is supported as indicated in the figure and loaded by a force P at x = Assume L = 10m, Pipe outer diameter (OD): 5", Pipe inner diameter (ID): 4.209", k = 1.0 x 10² N/m, Steel: E-2.1 x 10¹¹ N/m², P = 5000 N. Calculate the reaction forces at S and B. Show all work and FBD's as partial credit will be given. k www. P

A steel pipe is supported as indicated in the figure and loaded by a force P at x = Assume L = 10m, Pipe outer diameter (OD): 5", Pipe inner diameter (ID): 4.209", k = 1.0 x 10² N/m, Steel: E-2.1 x 10¹¹ N/m², P = 5000 N. Calculate the reaction forces at S and B. Show all work and FBD's as partial credit will be given. k www. P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The force in DB of the truss shown in below figure is W A 200 5 W tension O VW tension 5m 2 W compression √3 W compression E D 2W 5m B W
Help me urgent Two forces are applied ti the bar shown in the figure. Determine the normal and shearing stresses at point A, B and C?
3.1 Show your complete solution.
Solve the Problem, Thanks
H.W.# 2: Find the value of force (P) shown in figure if you know that the middle part of the rigidly fastened shaft is stressed to 400 Mia of tensile stress. Then calculate the stress in each of the other two end parts. = 40 mm² 10 kN A = 80 mm² A = 40 mm² 22 KN
Please provide the answer in three significant figures
Q 3. A rigid beam AB is 5.5 m long, hinged at point A and supported by two pipes at C and D as shown in figure 3 below. Pipe 1 at C is of copper has a outer diameter of 120 mm and inner diameter of 100 mm and yield stress of copper is 138 N/mm² Pipe 2 at D is of steel has a outer diameter of 100 mm and inner diameter of 90 mm and yield stress of steel is 250 N/mm2 Calculate the safe load at A if the load factor is 1.66 Pipe 1 Pipe 2 Psafe 2.3 m 2 m C 5.5 m Angle ACE = 0 Figure 3 Angle BDF = 42° Take 0 = 10 Page 7 of 7 PTO
The beam shown in the figure has three supports and a distributed load is applied to everything long with an intensity q = 5 Klb / ft. Determine the reactions at supports A, B, and C.
Determine the forces at each node in the figure and describe whether it is in compression or tension.
The force in DB of the truss shown in below figure is W A C O VW tension 5m √3 W compression 2 W compression 5 W tension E D 2W 5m B
Rods AB and BC have diameters of 2.9 mm and 4.6 mm, respectively. A force F = 2.4 kN is applied to the ring at B, as shown. (Figure 1) Determine the angle so that the average normal stress in each rod is equivalent. Express your answer to three significant figures. What is this stress? Express your answer to three significant figures and include appropriate units.
A simply supported steel beam is loaded with a uniformly distributed load and a torque. The beam has a U-shaped cross section, as shown. Determine the maximum normal compressive and tensile stresses caused by the acting loads. Express your answer in kgf/cm2 and in MPa.