A steel measuring tape used by a civil engineer is 50 m long and calibrated at 20oC.The tape measures a distance of 35.694m at 35oC. What is the actual distance measured? D = D L L T ( )( )( ) a Coefficient of linear expansion of steel a = 1.2 x 10-5oC-1

A steel measuring tape used by a civil engineer is 50 m long and calibrated at 20oC.The tape measures a distance of 35.694m at 35oC. What is the actual distance measured? D = D L L T ( )( )( ) a Coefficient of linear expansion of steel a = 1.2 x 10-5oC-1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A circular steel tube of length L = 59 inches is loaded in torsion by torques T (see the figure). r2 (a) If the inner radius of the tube is ri = 1.35 in. and the measured angle of twist between the ends is p = 0.5°, what is the shear strain y1 (in radians) at the inner surface? Round your answer to nearest whole. x10-6 rad Yi = (b) If the maximum allowable shear strain is 0.0004 rad and the angle of twist is to be kept at 0.5° by adjusting the torque T, what is the maximum permissible outer radius (r2).may? Round to two decimal places. (r2)max in.
The figure shows a cutaway view of an assembly in which a solid bronze [G = 6,500 ksi] rod (1) is fitted inside of an aluminum alloy [G = 4,000 ksi] tube (2). The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at A. The rod diameter is d1 = 1.45 in. The outside diameter of the tube is D2 = 3.2 in. and its wall thickness is t2 = 0.140 in. Overall dimensions of the assembly are a = 42 in. and b = 6 in. The allowable shear stresses for the bronze and aluminum materials are 10700 psi and 8100 psi, respectively. Further, the rotation angle of end B must be limited to a magnitude of 5.9°. Based on these constraints, what is the maximum torque TB that can be applied at end B?
3-12 A 10-mm-thick, low-alloy-steel plate 180 mm wide and 2000 mm long is subjected to a set of uniformly distributed frictional forces along its two edges, as shown in the figure. If the total decrease in the transverse 180-mm dimension at section a--a due to the applied forces is 16 x 10 mm, what is the total elongation of the bar in the longitudinal direction? Let E= 200 GPa and v= 0.25. Assume that the steel behaves as a linearly elastic material.
A STEEK ROD HAVING A CROSS SECTIONAL AREA OF 560mm2 IS SUSPENDED VERTICALLY IN ONE END. IT SUPPORTS A TENSILE LOAD OF 15KN AT THE LOWER END.
The figure shows a cutaway view of an assembly in which a solid bronze [G = 6,500 ksi] rod (1) is fitted inside of an aluminum alloy [G = 4,000 ksi] tube (2). The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at A. The rod diameter is d1 = 1.75 in. The outside diameter of the tube is D2 = 2.7 in. and its wall thickness is t2 = 0.130 in. Overall dimensions of the assembly are a = 38 in. and b = 13 in. The allowable shear stresses for the bronze and aluminum materials are 9400 psi and 7500 psi, respectively. Further, the rotation angle of end B must be limited to a magnitude of 5.1°. Based on these constraints, what is the maximum torque TB that can be applied at end B?
Q5) A specimen of alloy having a rectangular cross section of dimensions 5 mm x 16 mm is deformed in tension. Using the Load (N) Length (mm) tabulated data to plot the engineering stress – strain curve and 75.000 4669.56 75.03 then calculate the following: 8985.96 75.08 12694.14 75.09 (a) Modulus of elasticity. 16264.98 75.14 17991.54 75.18 (b) The yield strength. 19816.2 75.26 22484.52 75.421 (c) The modulus of resilience. 24623.1 75.621 26369.28 75.846 28292.04 77.68
A metallic rod made of steel as shown below is used as support for a signage with length equal to 150 meters and cross-sectional area of 300 mm?. It is suspended vertically and supports a tensile load of 20 kN. The properties of steel are as follows: E = 200 GPa Density of steel = 7850 kg/m³ Determine the total elongation of the steel rod considering its weight. fTNike TUBULAR
The figure shows a cutaway view of an assembly in which a solid bronze [G = 6,500 ksi] rod (1) is fitted inside of an aluminum alloy [G = 4,000 ksi] tube (2). The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at A. The rod diameter is d1 = 1.65 in. The outside diameter of the tube is D2 = 2.7 in. and its wall thickness is t2 = 0.130 in. Overall dimensions of the assembly are a = 49 in. and b = 11 in. The allowable shear stresses for the bronze and aluminum materials are 10500 psi and 7800 psi, respectively. Further, the rotation angle of end B must be limited to a magnitude of 5.6°. Based on these constraints, what is the maximum torque TB that can be applied at end B?
2. Consider a circular, semi-circular, and a quarter-circular steel plate, whose moment of inertia about the z-axis are Izc, Izs, and Izq, respectively. They have equal mass densities and thicknesses. Which of the following is correct? Izc=Izs>Izq Izc=Izs=Izq Izc>Izs>Izq Izc>lzs=Izq O X
Q.2) The assembly shown below is composed of an aluminum tube and a cylindrical steel plug. The mass density of aluminum and steel are 2700 kg/m³ and 7800 kg/m³, respectively. Find the coordinates of the mass center. y Tube A- Plug 20 mm 35 mm 100 100 A- mm mm Section A-A
A bar made of A-36 steel has the dimensions shown in the figure below. If an axial force of P = 100 kN is applied to the bar, determine the change in its length after applying the load. The material behaves elastically. Use a modulus of elasticity E = 200 GPa. y Diagram P= 100 kN Description automatically generated 80 mm 2 m P= 100 kN 160 mm
The band in the figure below is stainless steel (coefficient of linear expansion = 17.3 ✕ 10−6°C−1; Young's modulus = 18 ✕ 1010 N/m2). It is essentially circular with an initial mean radius of 5.4 mm, a height of 4.4 mm, and a thickness of 0.51 mm. If the band just fits snugly over the tooth when heated to a temperature of 81°C, what is the tension in the band when it cools to a temperature of 37°C?