A steel cable 2.0 m long has a cross-sectional area of 0.07 m2. A 200-kg machine is hung from the cable. Determine the stress and the strain: (Y_steel-20x10^10 Pa) Stress: 2.8x10^8Pa and Strain: 1.4 x 10-7 Stress: 280O0PA and Strain: 14000 Stress: 280OOPA and Strain: 1.4 x 10-7 Stress: 2.8x10^8Pa and Strain: 1.4 x 10-4

Q: A thin rectangular plate is uniformly, deformed, as shown. Determine the shear strain Yxy at P.…

A: Solution: The shear strain of the thin rectangular sheet in the y-direction can be obtained using…

Q: esteel plate if e rivets and the

A:

Q: 0.25 in. 5 in. 1 in. 0.25 in. -0.25 in. 2.5 in.

A: Maximum axial force P that can be applied to the steel plate

Q: A steel cube of side length L = 0.5 m is subjected to a shearing force of 5000N along the top…

A:

Q: A brass wire (E = 100 x 10° Nm2) which is 6.336 m long experienced an elongation of 1.21 mm by a…

A: Given, Young's modulus, E=100×109Nm2 Length, L=6.336m Elongation, ∆L=1.21×10-3m Mass, m=29kg a.…

Q: By applying 2.00 x 106 N/m2 shear stress to a steel bar 2 m in length, calculated the shear bending…

A: Shear Bending Stress(S) for steel is given as,    S=(8.3×108 N/m2)=Shear StressShear strain

Q: The beam is supported by a pin at C and an A- 36 steel guy wire AB. If the wire has a diameter of…

A: Solution:-Given thatDiameter of the wire (d)=0.2 inuniformely distributed load (w)=1000 lb per ft

Q: Find the stresses in members BC, BD, and CF for the truss shown in Indicate the tension or…

A:

Q: A steel cable with a radius of 1.5cm supports a chairlift at a ski area. If the maximum stress is…

A: The equation for the stress is given by,

Q: A tensile force of 2150 N is applied to a 12m steel beam with a cross-sectional area of 5.2 x 10-4…

A:

Q: A steel bar is stresses to 250 MPa. The modulus of elasticity is 250 GPa. The bar is 80 mm diameter…

A:

Q: material is applied by a tensile forces of 132 kN on a bar of the material with a cross- sectional…

A: stress is defined as the force per unit area. Write the expression for stress. S=FA…

Q: A wooden dowel is subjected to a shearing force of 715N on its top cylindrical face. If the dowel…

A: Shearing force F=715 N, diameter of dowel d=3cm (radius r=1.5cm), height of dowel h=11 cm and shear…

Q: ) A 54 kg diver is at the end of a diving board. That is 3.8 m long and has a mass of 26 kg. What is…

A:

Q: The screwgate carabiner is left open as it is loaded by a rope as shown. Calculate the stress state…

A: Stress is defined as force per unit area.  σ=FA Where F is a force and A is cross-section area.

Q: A 586-N object is hung from the end of a wire of cross-sectional area 0.04 cm2. The wire stretches…

A:

Q: N/m The young's modulus of a material whose elastic strain and stress are 1.45 and 108.96 N/m2…

A:

Q: a metal rod with length 2 m and cross sectional area of 0.002 m2 has a youngs modulus of 20x10^10Pa.…

A:

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s =…

A:

Q: 1.4 Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly…

A: P= 10 kN = 10 * 103 N AAl= 600 mm2 ABr= 400 mm2 ASteel= 300 mm2

Q: A sculpture weighing 75,757.5 N rests on a horizontal surface at the top of a 7.5-m-tall vertical…

A:

Q: The plot of tensile stress vs tensile strain of a certain rod has a slope of 23-GPa in the elastic…

A: Given data:  Slope of tensile stress vs tensile strain graph = 23 GPa Tensile strain (ε) =…

Q: A cable supports a lift that moves up with an upward acceleration of 2 m/s2. Given that the…

A: Given, Upward acceleration,a=2 m/s2 Proportional limit stress,σ=10.1×109N/m2 Area of…

Q: hear stre steel plat rivets and

A:

Q: An aluminium (p = 2.7g/cm³) wire is suspended from the ceiling and hangs vertically. How long must…

A:

Q: The young modulus of a material whose elastic strain and stress are 1.53 and 169.42 N/m²…

A: The elastic strain, strain=1.53   The stress, stress=169.42 N/m2

Q: The figure shows an approximate plot of stress versus strain for a spider-web thread, out to the…

A: We  have,  stress=forcearea and                strain=change in lengthoriginal lengthHence,  work…

Q: A 557-N force is applied to stretch a cable, 66-m long and has a cross-sectional area of 2.8 mm^2.…

A: Given, Force F=557NL=66mA=2.8mm2Y=1.0×1011N/m2

Q: The plot of tensile stress vs tensile strain of a certain rod has a slope of 25-GPa in the elastic…

A:

Q: An Aluminum cable of length 3.5 m has 15,000 N tensile force acting on it, if the wire is only…

A: Given, The length of the alumunium cable, L=3.5 m The tensile force acting, F=15000 N Length by…

Q: What shear stress is needed to produce a shear strain of 2.50 x 105 on an aluminum block?

A: Given data: Shear strain of Aluminum block is, εs=2.50×10-5.

Q: A 115 m long steel cable with a cross-sectional area of 1.13 x 10-4 m2 is subjected to a tensile…

A: Given- Length L= 115 m Cross-sectional area A= 1.13 x 10-4 m2  Tensile force F= 565 N

Q: The young's modulus of a material whose elastic strain and stress are 0.41 and 355.53 N/m?…

A:

Q: The stress experienced by a certain surface is 17612Pa when a 17-N force is applied to it. How much…

A:

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s =…

A: