A steel beam is used to carry a uniform load of 15 kN/m over a span of 6 m. The left support must be at the end but the right support can be placed at any reasonable distance from the right end. 1. Solve the distance from the right end where the support should be place so that the smallest beam can be used? 2. Solve the maximum moment. 3. Solve the flexural stress if it has a section modulus of 156,000 mm"

A steel beam is used to carry a uniform load of 15 kN/m over a span of 6 m. The left support must be at the end but the right support can be placed at any reasonable distance from the right end. 1. Solve the distance from the right end where the support should be place so that the smallest beam can be used? 2. Solve the maximum moment. 3. Solve the flexural stress if it has a section modulus of 156,000 mm"

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. The center post B of the assembly has an original length of 124.8 mm whereas posts A and C have a length of 125 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress in each post. The posts are made of aluminum and have a cross sectional area of 400 mm². Ea=70 GPa. Use the Force Method 100 mm -100 mm 800 kN/m 125 mm 800 kN/m
A reinforced rectangular beam with width b and effective depth d has 4.16 mm bars placed on 1 layer at the tension side. The beam has a stirrup with a diameter of 10 mm. Use fc=28 Mpa and fy=420 MPa GIVEN: b= 350 mm d= 600 mm L= 6 m Wd = 13 kN/m WL = 36 kN/m Calculate the nominal moment capacity of the beam Calculate that strain of the tension bars. Calculate the strength reduction factor of the beam
STATICS OF RIGID BODIES (CHOOSE THE CORRECT ANSWER IN THE CHOICES. WRITE THE SOLUTIONS LEGIBLY. NO LONG EXPLANATION NEEDED.)
#2 correct units pls.
Thumbs-Up will be given. Write the complette solutions legibly. Answer in 3 decimal places Structural Theory a. Determine the vertical reaction R₂ in KN. b. Determine the shear at midspan between vertical supports in KN c. Determine the maximum factored load moment in the beam in KN.m
Answer fast
Determine the maximum tensile or compressive stresses in the beam due to bending. The section has a base b= 140 mm and h= 240 mm PLACE THE ENTIRE PROCEDURE
In a plate girder subjected to a bending moment of 200 kNm, the width and thickness of flange are 200 mm and 10 mm respectively. What is the economical depth of the girder by assuming the moment is resisted by the flange only? (Take fy 250 MPa) = 000
I want the correct solution with proper explanation.
The pin-connected structure consists of two cold-rolled steel [E = 28,000 ksi] bars (1) and a bronze [E = 14,000 ksi] bar (2) that are connected at pin D. Each steel bar has a cross-sectional area of 0.375 in.?. A load of P = 18 kips is applied to the structure at pin D. Using a = 3.2 ft and b = 6.3 ft, calculate the area required for bar (2) so that each bar carries the same force. B (2) (1) (1) b D Answer: A2 = i in.2
4. A solid rectangular section beam, with cross-section 0.01m × 0.02m, and length 1m is simply supported at each end. A load of 80kg is applied at the middle of the span. The I-value of a rectangular section beam is given by: I = bh3 Calculate the maximum bending stress, ơmax 12
Correct answer.