A steel bar of rectangular cross-section 50 mm × 60 mm is pinned at one end and fixed at the other end. It is subjected to axial compression. If the proportional limit of the material is 240 MPa then (Take E= 210 × 103 MPa) A Ratio of minimum MOI and maximum MOI of the section is 0.694. Correct Option B Minimum length of the column is 1341.22 mm. © Minimum length of the column is 1896.916 mm. Correct Option Slenderness ratio is used as a parameter to differentiate between long and short columns. Correct Option

A steel bar of rectangular cross-section 50 mm × 60 mm is pinned at one end and fixed at the other end. It is subjected to axial compression. If the proportional limit of the material is 240 MPa then (Take E= 210 × 103 MPa) A Ratio of minimum MOI and maximum MOI of the section is 0.694. Correct Option B Minimum length of the column is 1341.22 mm. © Minimum length of the column is 1896.916 mm. Correct Option Slenderness ratio is used as a parameter to differentiate between long and short columns. Correct Option

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I need the answer quickly
Solution w/FBD
Read the question carefully and give me the right solutions with clear calculation.
Determine the compressive force (in lb) in the bars shown after a temperature rise of 173°F if d = 0.015 in. Round off the final answer to five decimal places. Use the following data: Bronze Aluminum A = 2.24 sq. in A = 2.78 sq. in E = 14959726 psi E = 10594540 psi L = 12.5 in L = 16.6 in α = 11.61 x 10-6/ °F α = 12.67 x 10-6/°F
What maximum load P can be applied without exceeding an allowable stress of 70 MPa for aluminum or 120 MPa for steel? Can a larger load P be carried if the length of the aluminum rod is changed. the length of the steel portion being kept the same? If so, determine this length
Round off final ans only, dont round initial values
Use the giuven values: Aluminum: E = 10 x 106 psi, α = 12.8 × 10-6 in/(in·°F) Bronze: E = 12 x 106 psi, α = 10.5 × 10-6 in/(in·°F) Show you complete solution.
SHOW COMPLETE SOLUTION AND DRAW ILLUSTRATION
The aluminum W 310 x 202 (wide flange) column is subjected to an eccentric axial load P as shown. The maximum compressive stress in the column is given by the so-called secant formula: where --- [¹ + ( √5)] ec o 1+ sec max E ō = P/A = average stress A = 25800 mm² = cross-sectional area of the column e = 85 mm = eccentricity of the load c = 170 mm = half depth of the column r = 142 mm = radius of gyration of the cross section L = 7100 mm = length of the column E = 71 x 10⁹ Pa = modulus of elasticity Determine the maximum load P that the column can carry if the maximum stress is not to exceed 120 × 10^6 Pa. Terminate the computation when Σa < 0.0005%.
A round bar made of same material consists of 3 parts each of 100 mm, length having diameters of 40 mm, 50 mm and 60 mm respectively. If the bar is subjected to an axial load of 10 kN, the total elongation of the bar would be (E is the modulus of elasticity in KN/mm². (a) 4/1 1 1 + + (b) TE 16 25 36 (c) 1 0.4 1 1 + wwwwww + TE 16 25 36 (d) 4√2/1 1 1 www + wwwwwww + TE 16 25 36 40/1 1 1 + TE 16 25 36 — ===== + — mm mm mm mm
A rectangular steel block is 3.2 inches long in the x-direction, 2.9 inches long in the y-direction, and 4.5 inches long in the z-direction. The block is subjected to a tri-axial loading of three uniformly distributed forces as follows: 48 kips tension in the x-direction, 65 kips compression in the y-direction, and 54 kips tension in the z-direction. If Poisson's ratio is 0.30 and E = 29 x 106 psi, find the uniformly distributed load that must be added in the x-direction to produced no deformation in the z-direction. Your final answer should include two decimal places
A rectangular steel block is 3.0 inches long in the x-direction, 3.0 inches long in the y-direction, and 4.5 inches long in the z-direction. The block is subjected to a tri-axial loading of three uniformly distributed forces as follows: 50 kips tension in the x-direction, 60 kips compression in the y-direction, and 54 kips tension in the z-direction. If Poisson's ratio is 0.30 and E = 29 x 106 psi, find the uniformly distributed load that must be added in the x-direction to produced no deformation in the z-direction. Your final answer should include two decimal places