A steel bar has a uniform cross sectional area of 300mm². Calculate the stress at member AB 1.6m 1.2m 1.8m 25N SKN

Q: The distributed load is supported by a box beam as shown below. Determine the maximum value of wo…

A:

Q: Draw Mohr's circle for the state of stress defined by 01 = 80 MPa, o2 = -20 MPa and t12= 40 MPa. (1…

A: To draw mohr's circle for the state of stress

Q: Cônnecting Ród óf å Diesel Engine cross section. It is subjected to a force of 85KN. Calculate the…

A: area of the I cross section is =2×21×6   +   5×35=427mm2=427×10-6m2

Q: Finding the cross sectional area Stress 22.66 N/mm2 Force=2 N

A: Given data : Force is denoted by F Stress is denoted by σ   Required : Cross sectional area

Q: Solve for the indentation diameter if the BHN of the material is 70 and a 500 kg of load is applied?…

A:

Q: Determine stress produced by tensile force of 20 N applied on cross sectional area of 5 mm2

A: Given data: Tensile force (F) = 20 N Cross sectional area (A) = 5 mm2 Need to determine the stress…

Q: A load Q-200kN is applied to a rigid plank MN as shown. At ends M and N, vertical brass and bronze…

A:

Q: A 150 min x a mnm x 20 mm stecl plate is subjected a pull of 150 kN along its central axis as show…

A:

Q: The rigid bar ABC supports a load of 21.1 kN at point C. A circular rod (diameter 25 mm) supports…

A: Given:

Q: Draw and stress tensonr with the following characteristics The stress cube visualization at point…

A:

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

A:

Q: If a pipe with an inner diameter of 36 mm is subjected to an axial load of 5.20 x 105 N and the…

A: To read quetsion carefully

Q: If each grid in Mohrs circle below is 15 MPa then the maximum principal stress is: 1 grid square =…

A: It is the very basic question of mechanics of material portion. Used concept is nomenclature of…

Q: The force P is applied on the top of the solid cylindrical body which rests on a circular cap as…

A:

Q: A tank 10 m high and 2 m in diameter is 15 mm thick. The max tangential stress is ? The max…

A: Given data  height = 10 m diameter = 2 m thickness = 15 mm find the maximum tangential stress and…

Q: machine having a mass of 9555 kg is supported by three solid steel rods arranged as showed in the…

A:

Q: The bar shown is subjected to a moment of 6000 lb.in. Calculate the maximum stress developed in the…

A:

Q: stress in the segment QR

A: Given; A bar having cross-sectional area(A)=700 mm2Various loads at the positions indicated at the…

Q: The horizontal cross-section of the cast-iron standard of a vertical drilling machine has the form…

A: To find: The greatest value of thrust and the stress along the face AB. Given: The tensile stress…

Q: The plastic pipe AC has a hollow circular cross- section as shown to the right. Determine the normal…

A:

Q: 1:in the following arrangement of structur allowable shear stress in pin C is 16 Mpa calculate the…

A: Given;- W=36N/m D=10mm Shear stress=16Mpa

Q: In the figure, when the torture squeezes the material, the maximum force F in the clamping jaws is…

A:

Q: 1. A BRONZE ROD IS SUBJECTED TO A TENSILE LOAD OF 15,000N. IF ITS ALLOWABLE STRESS IS 75 MPa,…

A: GivenP=15000NLi=40mmLo=L=?σallow=75MPa=75 N/mm2

Q: Bar (1) has a cross-sectional area of 0.75 in.2. If the stress in bar (1) must be limited to 49 ksi,…

A: Correct answer: (iv) 22.05 kips

Q: Calculate the values of ol and o3 in the rock if the differential stress is 40 MPa and the center is…

A: differential stress = 40 MPa. (diameter of the Mohr's circle).Therefore, the radius of the Mohr's…

Q: The figure shows the cross section of a circular steel tube that is filled with concrete with a…

A: Find the stress in concrete.

Q: Mohr's circle for an element is shown, each grid is 5 MPa square. A rotated plane through the…

A:

Q: Determine stress Force=40 KN Cross sectional area =4 mm2

A: Given:-Force=40 KN=40×103 NArea=4 mm2=4×10-6 m2To find:-Stress

Q: Calculate the stress at a-a and b-b sections

A: FBD of AB & BC

Q: 3. The aluminum block has the rectangular cross-section and is subjected to an axial compressive…

A:

Q: 1- Calculate the stresses in members CE, DE, and DF. The cross-sectional area of each member is 1200…

A:

Q: 1. Find the internal force of member EG, FH, and FG using method of sections. 0.866 m 3KN 5 @ 1m

A:

Q: Find stress in each segment. Diameter of AB is 2in and diameter of BC is 1in.

A:

Q: For the ring and the load applied. Calculate the normal stresses at point A and B. Hint: Normal…

A: Given: The axial load on the ring=400 N Because axial load is equally distributed in both parts of…

Q: compute the maximum stress in the member, considering stress concentrations.

A:

Q: Mohr's circle for an element is shown, each grid is 5 MPa square. A rotated plane through the…

A:

Q: The truss to the right is comprised of members with cross sectional area A = 3 in', length of 12…

A:

Q: A square hollow bar has a breadth and depth of 30mm and a wall thickness of 2mm. A tensile force of…

A:

Q: Find the stress if 1002 lb force applied on 12 in2

A: Given data : Force=P Cross sectional area=A   To find : Stress