A steel bar has a cross-sectional area of 10-³ m², Young's modulus of 2 × 10" Pa and Poisson's ratio of 0.4. If the bar is subject to a compressive force of 10° N, find the corresponding longitudinal and transverse strains. 8.17 8.18 Two strain gauges, each with an unstrained resistance of 120 N and a gauge factor of 2.0, are bonded onto the steel bar of Problem 8.17 so that one measures the longitudinal strain and one the transverse strain. Find the corresponding gauge resistances for the longitudinal and transverse strains.

Q: Problems in Design of PCBs for Digital Circuits CROSS-TALK To reduce cross-talk, lower frequency…

A: We need to discuss the  factors to minimize cross-talk in designing of PCB .

Q: What is the typical response time for MOV's?

A: MOV's are being used to prevent the electronic components in the power system during the occurrence…

Q: 3. Show with the aid of equations and block diagram the generation of (USB) signal by using phase…

A: Figure shows block diagram of phase shift method of SSB generation in which carrier and one of the…

Q: discuss how the information signal is recovered from an FM signal using slope detector

A: Slope detector is a demodulation of frequency modulated signal.     Frequency modulation is a angle…

Q: (b) Figure Q.4b shows an Adder/Subtractor circuit implemented using Adder Q. The delay for XOR = 21,…

A:

Q: Q4:A: With the aid of diagram show the operation of microprocessor based relay, then give the…

A:

Q: When a processor responds to a RQ/GT0, the value of MN/MX would be __________________ a. 1 b. 0 c.…

A: The explanation is as follows.

Q: Draw block diagram /circuit diagram of the ff. FM circuits and discuss the operation.  D. PHASE…

A: Phase locked loop works on the same principle as synchronous detector.

Q: Based on example related on relay + switch as shown during lecture session, state the configuration…

A:

Q: 10- The average value state that: a) algebraic sum of length / the areas of curve. b) algebraic sum…

A: Average value of signal = 1T∫0Tx(t) dt Where T is the length of the curve x(t)

Q: Explain why Ray theory is not sufficient to describe wave propagation in OFS What are the advantages…

A: This question has multi-parts. I have solve only two parts. In analyzing the transmission of sound…

Q: For the following reading of circuit current are [8, 8.2, 9, 7.8, 9.1, 8.5, 7.7, 7.9, 8, 8.1] mA.…

A:

Q: Explain the following (a) sensitivity of a receiver (b) selectivity of a receiver. Why are these…

A: (a) Sensitivity of a receiver is minimum input signal required to produce a specified output…

Q: 8.19 List the contents of registers C, A, Q, and P in a manner similar to Table 8.5 during the…

A: Given, The multiplicand is 11011. The multiplier is 10111. Let the given multiplicand be B. So, B =…

Q: what is the effect. low cost operation amplifier in optical fiber system ?

A: The optical amplifier is a gadget which gets some information signal and produces a yield signal…

Q: An AM signal as shown below. The carrier frequency is 600 Hz, and the modulating signal is a…

A: 1) It is DSBSC AM signal

Q: Why we use FT-IR instrumentation?  Please shortly answer at your own words.

A: The explanation is as follows.

Q: (b) In a junction of road installed with traffic light, the sensor circuit with capablities to…

A: Given: In a junction of a road installed with a traffic light, the sensor circuit with capabilities…

Q: Problem-6. Consider a noiseless channel need to carry human voice and to be transmitted with four…

A: Considering human voice at maximum frequency vibrations upto 4 kHz. So maximum frequency component…

Q: Topic: Amplitude Modulation and Demodulation: please answer this question thanks. 1. What are the…

A: Brief description: Envelope detector is a demodulator circuit which is used to demodulate amplitude…

Q: If there is one TDM equation for each component,can each equation be solved independently of the…

A: Time Division Multiplexing is a technique to transmit multiple signal through a singl channel…

Q: In balance slope detection method if the signal has a high value of amplitude, how the interference…

A:

Q: find the system Noise factor and Noise Figure for Te = 30,50,75,150, and 300 K %3D measured at To of…

A: Given: The effective noise temperature measured at reference temperature 290K is: Te=30, 50, 75,…

Q: 1-Why PPM is said to be better than PWM?

A: As per Bartleby guidelines we are allowed to solve only one question, please ask the rest again.

Q: Show with a diagram that FM and PM are equivalent and interchangeable. Briefly explain why the…

A: According to the question we need to show with a diagram that FM and PM are equivalent and…

Q: 6. BJT is more linear than FET. Why? Explain

A:

Q: Q24) This multiple choice question from DIGITAL COMMUNICATIONS course. just write for me the final…

A:

Q: 7. The substrate of MOSFET is normally connected to the Drain terminal. 8. In the actual…

A: Given  True or false question based on MOSFET and BJT. Please find the below attachment for clear…

Q: What is the function of mccb and rccb? Disadvantages two required?

A: The main purpose of an MCCB is to provide a way to manually open a circuit or automatically open a…

Q: Write the background study of the wifi antenna

A: Wifi Antenna :  Antennas are vital for wi-fi neighborhood area networks (WLAN). They facilitate the…

BJT (Bipolar Junction Transistor)

A BJT is a semiconductor device with 3 terminals that consist of a p-n junction diode that can amplify the signal or current. It is a current-controlled device. The three BJT terminals are base, collector, and emitter. The BJT works with the charge carrier, the two type of carriers in the BJT are holes and electrons, the charge carriers flow by the process of recombination. The signal to be amplifier is generally given as the input at the base terminal and an amplified form of it is available at the collector terminal.