Answered: A steam turbine is operated under the…

A steam turbine is operated under the conditions shown in the figure. Define: a. steam flow rate (kg/min) to produce 1000 kW power b. actual steam rate (kg/kWh)! c. turbine efficiency

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Show the whole process. (Conversion of Units)
A power plant uses steam flowing at 75kg/s to perform power cycle. Both the turbine and the pump operate adiabatically and without irreversibilities. a) find quality at the turbine exit b) find mass flow rate (kg/s) of cooling water through the condenser c) find efficiency of the cycle d) plot the cycle on a T-s diagram, indicate the saturation curve and each state of the working fluid.
You have been asked to help with the low-pressure compressor (LPC) design for a turbofan engine with a bypass ratio of 8.4. The preliminary cycle design calls for the LPC to produce a pressure ratio of 9.4 with the following operating conditions and constraints. .Inlet Conditions TO2 Poz Core Air Mass Flowrate (kg/s) (K) (kPa) 282 24.6 47.0 Design Constraints Maximum Polytropic Efficiency 94.1% Maximum Stage Pr 1.55 Estimate the minimum number of stages required for this LPC. Then assuming the 1st stage of the LPC operates at the maximum allowable pressure ratio, determine the stagnation temperature exiting the 1st stage, and the stage's adiabatic efficiency. Also determine the power (W) required to operate the full LPC (not just 1st stage). Finally, what would be the percent change in the required power if the polytropic efficiency was only 90.0%.
Answer this ASAP,thx In a steam turbine, saturated steam enters the turbine at a pressure of 16 MPa and a pressure in the condenser of 8 kPa. The mass flow rate of the fluid entering the turbine is 100 kg/s. calculate: A) the power produced B) the rate of heat transferred to the steam passing through the boiler C) the thermal efficiency
Solve and choose the correct A Simple Steam Power Plant under the conditions shown in the diagram. Neglect Kinetic Energy and Potential Energy across the power plant and (2) :neglect the heat transfer from the turbine. Choose the correct answers The power done by the turbine 12 MW. The heat supplied to Boiler 45.7 MW O The power done by the turbine 8 MW. The heat supplied to Boiler 25.7 MW O The power done by the turbine 10 MW. The heat supplied to Boiler 15.7 MW O) The power done by the turbine 12 MW. The heat supplied to Boiler 25.7 MW C P1 = P4, T1 = 500°C =8 kgs m steam Turbine turbine (Adiabatic) O P = 20 kPa X2=09 Boiler Condenser P4 10 MPa Rcond AT=10°C (max) T4 = T3 Feedwater +mwater Cooling water Pump P3 P T3 = 40°C
8. A turbine passes 67.5 kg/h of steam at 200 km/h at 8 MPa and leaves at 0.5 MPa as wet steam with a speed of 90 km/h and a specific volume of 0.189 m3/kg. d. What must be the steam input conditions (T,H) to turn on a device that consumes 30 kW? and. What is the mass and volumetric flow rate of the water at the outlet? F. What is the input and output area?
Problem 4: Consider the following schematic of a simple turbojet engine model that uses air as its working fluid. With the data given determine (D) the amount of power required by the compressor, and (E) the velocity of the exhaust stream at the exit of the system. Note: The variable rp is the compressor ratio defined to be the pressure of the compressor exit to the pressure of the compressor inlet. Assume that the compressor, turbine, and nozzle are all adiabatic and reversible. The Turbojet Engine 2 P = P; : 100 kPa Burner T,: 300 k 6: 12 : (200 K $/h が FHV = 43 KJ/g- frel ト

A gas increases in pressure from 2 atm to 6 atm at a constant volume of 1 m3. It then expands at a constant pressure to 3 m3, it then returns to the starting conditions in a transformation that makes a triangle. A) Calculate the work done in the cycle. B) If the cycle deposits 500 kJ to the low temperature reservoir, find the heat taken from the high temperature reservoir and the efficiency of the engine. R=8.314 J/K*mol , 1atm=101325 Pa
A reversible engine receives heat from a source at 800 ° C some heat goes to a sink at a temperature of 25 ° C. If the motor receives a heat flow of 1200 kJ / min find: a) The thermal efficiency of the motor and b) The working power output of the motor are in kW. Ans: a)η=72.2% b)Ẇ=14.44kW
Question 2 A hydro-electric power station has a reservoir area of 3,8-km2 and a capacity of 9,9 x 106 m3 . The effective head of water is 100 metres. The penstock, turbine and generation efficiencies are 95%, 90%, and 85%, respectively. 2.1 Determine the overall efficiency of the power station (%) and determine the total electrical energy that can be generated from the power station (kWh). 2.2 Determine the depth of the reservoir (metres) 2.3Determine the fall in reservoir volume level is the load of 100 kW is supplied for 5 hours (%).
Determine the compressor work, W,comp. And the condenser heat transfer, Qc.
Question B3 The engine of an aeroplane is equipped with an ideal convergent nozzle with an area ratio Ainlet 2.035 ( -A-2.035), as in Figure Q-B3. The aeroplane is flying at an altitude of 11 Aexit km where the atmospheric pressure and temperature are 0.23 bar and 216K respectively. You may assume the combustion gases entering the nozzle have the same property as air (i.e. y=1.40, R=287 J/kgK and Cp-1004.5J/kgK). Page 6 Question B3 continued inlet exit Amles/Aexit -AVAJ-2.035 Figure Q-B3 a) If the nozzle operates at its critical condition, calculate: the inlet Mach number M;. nozzle's exit velocity V, the inlet stagnation pressure Por- the inlet static pressure FG The stagnation Aj P, and the nozzle's gross thrust per unit exit area temperature of the gases entering the nozzle is To 1200 K. b) If the stagnation pressure at the inlet of the nozzle is reduced to 80% of its value in part (a), determine the exit static temperature 7;, the nozzle's gross thrust per unit exit area FG. The…